The Sportster and Buell Motorcycle Forum - The XLFORUM®
 

Go Back   The Sportster and Buell Motorcycle Forum - The XLFORUM® > BUELL MOTORCYCLE FORUM > Buell Motorcycle Transmission, Clutch, Primary & Secondary Drive
XLF Blogs XLF Arcade XLF Disclaimer/Privacy Statement/Terms Of Use

Notices

Active Threads
0 How many miles are on your sporty?
Last Post: FearTheBeard
Posted On: 3 Minutes Ago
Replies: 1,140
Views: 257,352
0 Gravydog crashed again.
Last Post: gravydog
Posted On: 3 Minutes Ago
Replies: 36
Views: 803
0 Saddlemen step up seat on 07-09
Last Post: 07xlc1200
Posted On: 12 Minutes Ago
Replies: 7
Views: 207
0 Moto Guzzi V9 Bobber debut
Last Post: Bone
Posted On: 14 Minutes Ago
Replies: 31
Views: 1,059
0 XR-Cafe-Conversion
Last Post: tomaso
Posted On: 15 Minutes Ago
Replies: 301
Views: 53,151
0 Replacement Fuel line?
Last Post: Diogenes415
Posted On: 24 Minutes Ago
Replies: 20
Views: 607
0 Carb + Rubbermount = Collector's Item?
Last Post: Ireeman
Posted On: 26 Minutes Ago
Replies: 171
Views: 27,169
0 Troy Corser racing 1929 BMW R57 Compressor at Goodwood Revival
Last Post: tigger
Posted On: 33 Minutes Ago
Replies: 0
Views: 7
0 4D world
Last Post: Ireeman
Posted On: 48 Minutes Ago
Replies: 4
Views: 208
0 Howdy y'all
Last Post: Folkie
Posted On: 1 Hour Ago
Replies: 1
Views: 9
5 No power to ignition, intermitently
Last Post: Shuffle
Posted On: 1 Hour Ago
Replies: 0
Views: 9
0 Electrical Problem with '77 XLH-no power
Last Post: 60weight
Posted On: 1 Hour Ago
Replies: 55
Views: 1,763
0 Official XL Forum Random Image Thread (NO NUDITY!)
Last Post: Ireeman
Posted On: 1 Hour Ago
Replies: 41,542
Views: 6,386,828
0 Good kid or Bad Kid??
Last Post: Ireeman
Posted On: 1 Hour Ago
Replies: 120
Views: 15,765
0 Sheared Pinion Shaft Key
Last Post: Hippysmack
Posted On: 1 Hour Ago
Replies: 17
Views: 314
0 THE Trainspotting Thread
Last Post: Stairman
Posted On: 1 Hour Ago
Replies: 2,097
Views: 230,553
0 Shotgun Porn
Last Post: Ireeman
Posted On: 1 Hour Ago
Replies: 810
Views: 109,486
0 "S" model specific Q&A
Last Post: LocoLocal
Posted On: 1 Hour Ago
Replies: 1,795
Views: 337,785
0 You asked for it! "The Tess' Coffee Thread"
Last Post: Ireeman
Posted On: 1 Hour Ago
Replies: 10,287
Views: 692,238
0 Throttle cable/housing
Last Post: doodah man
Posted On: 1 Hour Ago
Replies: 1
Views: 41
0 Thursday 27th September 2018: The Harroway; Sefton Warren To Powderham Castle
Last Post: Folkie
Posted On: 2 Hours Ago
Replies: 11
Views: 1,462
0 ....1
Last Post: Graywolf
Posted On: 2 Hours Ago
Replies: 4,631
Views: 220,464
0 ‘17 Roadster no start...
Last Post: ADK XL
Posted On: 2 Hours Ago
Replies: 37
Views: 1,661
0 mode of failure
Last Post: Graywolf
Posted On: 3 Hours Ago
Replies: 9
Views: 239
0 Roads I'd like to ride.
Last Post: Stairman
Posted On: 4 Hours Ago
Replies: 457
Views: 20,927
0 Range With EFI 3.3 Gal Tank
Last Post: xElvis
Posted On: 4 Hours Ago
Replies: 94
Views: 48,721
0 Out of the Box Thinking
Last Post: GA_Ironhead
Posted On: 5 Hours Ago
Replies: 13
Views: 786
0 2020 H-D response to the Indian FTR1200?
Last Post: Bwf347
Posted On: 5 Hours Ago
Replies: 98
Views: 5,469
0 Hottie of the day, no nudity.
Last Post: Stairman
Posted On: 6 Hours Ago
Replies: 8,051
Views: 619,683
0 fat man on a sportster
Last Post: Four Speed
Posted On: 6 Hours Ago
Replies: 8
Views: 1,327
More...
Members Birthdays
Sponsored Links
Reply
 
Share Thread Tools Display Modes
  #1  
Old 13th June 2017
Airbozo's Avatar
Airbozo Airbozo is offline
XL FORUM TEAM MEMBER
 
Join Date: Mar 2009
Location: Santa Cruz Mountains
Posts: 1,386
Sportster/Buell Model: XLH1200
Sportster/Buell Year: 1995
Sportster/Buell Model #2: S3T Thunderbolt
Sportster/Buell Year #2: 2000
Other Motorcycle Model: XB12R
Other Motorcycle Year: 2009
Reputation: 1179682
Airbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond repute
Default Primary chain adjustment without the window

Here's the deal:

My 2000 S3T had a few issues last year. I ended up replacing the main shaft bearing (and made my own tool to do it), and that has stopped the oil from blowing out the vent hose and dripping on the tire.

My issue is that when I went to open up the side cover, I noticed that one of the screws holding the primary chain inspection cover had a stripped head. I tried several tricks to remove it before breaking out the Speed-outs (didn't work) and another screw extractor (not a cheap one either).

I am not new to this procedure and I was really surprised when the screw extractor broke off in the screw head... So I break out the mini drill press, rig up a strap clamp and 'uge! c clamp to hold it in position as I attempt to drill out the screw extractor. The bit drifted and started a hole next to the extractor, so I stopped. I cannot get that damn screw out and it should not be in that tight. I even heated it up a little bit, but not enough to melt the o-ring. So I figure I do not have the right tools or skill to get that screw out, but I would like to make a temporary primary chain adjustment, so I can get this bike to the shop so they can try to remove that screw.

Is there a procedure I can follow, that will allow me to tighten the primary chain so I can ride the bike a bit without having access to the inspection cover??

Is there any other way I can try to remove the screw without damaging the cover?

Thanks!
__________________
"...Dumb all over, A little ugly on the side... "...Frank Zappa...
Reply With Quote
  #2  
Old 13th June 2017
Screw Loose Dan's Avatar
Screw Loose Dan Screw Loose Dan is offline
I think I like Sportsters
 
Join Date: Oct 2006
Location: Collegeville, PA
Posts: 6,998
Sportster/Buell Model: 883L (sorta) & a 1200R
Sportster/Buell Year: 2007
Sportster/Buell Model #2: 1200CX
Sportster/Buell Year #2: 2016
Other Motorcycle Model: XR1200X
Other Motorcycle Year: 2012
Reputation: 2704588
Screw Loose Dan has a reputation beyond reputeScrew Loose Dan has a reputation beyond reputeScrew Loose Dan has a reputation beyond reputeScrew Loose Dan has a reputation beyond reputeScrew Loose Dan has a reputation beyond reputeScrew Loose Dan has a reputation beyond reputeScrew Loose Dan has a reputation beyond reputeScrew Loose Dan has a reputation beyond reputeScrew Loose Dan has a reputation beyond reputeScrew Loose Dan has a reputation beyond reputeScrew Loose Dan has a reputation beyond repute
Default

I read on here a long time ago about adjusting the primary chain (on Sportsters) by sound. Ever since, that's the way I've done it. I usually start by using the inspection cover but always fine tune it by listening. You don't want the chain to whine (too tight) but you don't want it slapping around (too loose). Adjust the chain with the bike running and you'll hear it. Tighten until it whine's a little, then back it off just a bit.

Is there a reason this wouldn't work the same way on a Buell?

See some discussion about it in this sticky thread.
__________________
Screw Loose Dan
Current fleet:
2007 - 1200R (Orange bike)
2012 - XR1200X (XR)
2016 - 1200CX Roadster (new one)
2007 - 883L/90" -current project - (Black bike)
Reply With Quote
  #3  
Old 13th June 2017
sportsterpaul's Avatar
sportsterpaul sportsterpaul is offline
XL FORUM TEAM MEMBER
 
Join Date: Jan 2009
Location: In a swamp/Michigan
Posts: 12,645
Sportster/Buell Model: XL1460C
Sportster/Buell Year: 2000
Sportster/Buell Model #2: XL1200R
Sportster/Buell Year #2: 2006
Other Motorcycle Model: XL1200R
Other Motorcycle Year: 2004
Reputation: 7121784
sportsterpaul has a reputation beyond reputesportsterpaul has a reputation beyond reputesportsterpaul has a reputation beyond reputesportsterpaul has a reputation beyond reputesportsterpaul has a reputation beyond reputesportsterpaul has a reputation beyond reputesportsterpaul has a reputation beyond reputesportsterpaul has a reputation beyond reputesportsterpaul has a reputation beyond reputesportsterpaul has a reputation beyond reputesportsterpaul has a reputation beyond repute
Default Primary chain adjustment

Just want to add a note, this " ear" adjustment works best if the power plant is warmed up. Been doing it for over a dozen years without issue.
__________________
I.B.A.#26543, Growing old-Mandatory/ Growing up-optional. Men do not quit playing because they get old, they get old because they stop playing!

The XL Forum Sportsterpedia:
http://sportsterpedia.com/doku.php/starthttp://xlforum.net/forums/images/editor/quote.gif
Reply With Quote
  #4  
Old 13th June 2017
r4fthrs's Avatar
r4fthrs r4fthrs is offline
Flat Track Champion
 
Join Date: Nov 2009
Location: Rolling hills of S. IN
Posts: 633
Sportster/Buell Model: 1200 Custom
Sportster/Buell Year: 07
Reputation: 1176869
r4fthrs has a reputation beyond reputer4fthrs has a reputation beyond reputer4fthrs has a reputation beyond reputer4fthrs has a reputation beyond reputer4fthrs has a reputation beyond reputer4fthrs has a reputation beyond reputer4fthrs has a reputation beyond reputer4fthrs has a reputation beyond reputer4fthrs has a reputation beyond reputer4fthrs has a reputation beyond reputer4fthrs has a reputation beyond repute
Default

Airbozo - have the same problem my inspection cover screw head has been stripped for 4 years. I do the method Screw Loose Dan suggests and I think it is the better method. When I did it the Moco way I always ended up doing it two to three times before it was right (would either whine when it was hot or rattle when cold).

Adjust it when hot, slowly tighten the adjusted until it slightly whines and back off until the whine stops and an additional 1/4 turn and it is perfect every time. The company advises against it because if you accidentally hit the shifter the bike will take off, but if you are concerned about safety, put it on a center jack and lift the back wheel.
__________________
Armed you are a citizen, unarmed a subject.
Fear the government who fears your guns.
An armed society is a polite society.
Reply With Quote
  #5  
Old 13th June 2017
Airbozo's Avatar
Airbozo Airbozo is offline
XL FORUM TEAM MEMBER
 
Join Date: Mar 2009
Location: Santa Cruz Mountains
Posts: 1,386
Sportster/Buell Model: XLH1200
Sportster/Buell Year: 1995
Sportster/Buell Model #2: S3T Thunderbolt
Sportster/Buell Year #2: 2000
Other Motorcycle Model: XB12R
Other Motorcycle Year: 2009
Reputation: 1179682
Airbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond reputeAirbozo has a reputation beyond repute
Default

Excellent information on the adjustment. I thought I read something similar, but could not find it during a search.

I ran out of time to try this until I get back from vacation, but I will attempt it then. Thanks a lot for the info!
Reply With Quote
  #6  
Old 13th June 2017
The Crusher's Avatar
The Crusher The Crusher is offline
XL FORUM TEAM MEMBER
 
Join Date: Aug 2015
Posts: 851
Sportster/Buell Model: 883/1200
Sportster/Buell Year: 1996
Reputation: 1149983
The Crusher has a reputation beyond reputeThe Crusher has a reputation beyond reputeThe Crusher has a reputation beyond reputeThe Crusher has a reputation beyond reputeThe Crusher has a reputation beyond reputeThe Crusher has a reputation beyond reputeThe Crusher has a reputation beyond reputeThe Crusher has a reputation beyond reputeThe Crusher has a reputation beyond reputeThe Crusher has a reputation beyond reputeThe Crusher has a reputation beyond repute
Default

Quote:
Originally Posted by Screw Loose Dan View Post
Adjust the chain with the bike running and you'll hear it. Tighten until it whine's a little, then back it off just a bit.


See some discussion about it in this sticky thread.
Hot damn. I KNEW there had to be a better way. Sometimes things pop up on this site randomly that really help.

Thanks.
__________________
You can't keep a good man down......... unless you tie weights to his ankles.
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Sponsored Links
All times are GMT +1. The time now is 00:19.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
XL Forum® - Linson Media LLC