The Sportster and Buell Motorcycle Forum - The XLFORUM®
 

Go Back   The Sportster and Buell Motorcycle Forum - The XLFORUM® > SPORTSTER MOTORCYCLE FORUM > Sportster Motorcycle Drivetrain > Sportster Motorcycle Transmission, Clutch, Primary & Secondary Drive
XLF Blogs XLF Arcade XLF Disclaimer/Privacy Statement/Terms Of Use

Sportster Motorcycle Transmission, Clutch, Primary & Secondary Drive Transmission, Clutch and primary or secondary drive problems, advice, and/or how tos.

Active Threads
0 Seeking advice on shorter rear shocks
Last Post: Gulf Coaster
Posted On: 1 Minute Ago
Replies: 22
Views: 674
0 Cases Full Of Oil
Last Post: Maxeffort
Posted On: 16 Minutes Ago
Replies: 2
Views: 54
0 Loose oil pump feed fitting - 2019 Iron
Last Post: NGOT8R
Posted On: 19 Minutes Ago
Replies: 2
Views: 29
0 Speed
Last Post: NLXL
Posted On: 20 Minutes Ago
Replies: 43
Views: 578
0 Still got your upper drive belt guard??
Last Post: Folkie
Posted On: 56 Minutes Ago
Replies: 116
Views: 19,610
0 Official XL Forum Random Image Thread (NO NUDITY!)
Last Post: Graywolf
Posted On: 1 Hour Ago
Replies: 45,537
Views: 7,191,703
0 98 Stator Removal / Inspection / Installation
Last Post: Hippysmack
Posted On: 1 Hour Ago
Replies: 57
Views: 1,457
0 Powerraythor conversion
Last Post: ferretface
Posted On: 1 Hour Ago
Replies: 29
Views: 1,040
0 Hottie of the day, no nudity.
Last Post: Stairman
Posted On: 1 Hour Ago
Replies: 15,111
Views: 1,433,523
0 On starting a new thread
Last Post: IronMick
Posted On: 1 Hour Ago
Replies: 20
Views: 409
0 never mind
Last Post: Maxeffort
Posted On: 1 Hour Ago
Replies: 9
Views: 312
0 Deer hunting at stairman's.
Last Post: sportsterdoc
Posted On: 1 Hour Ago
Replies: 13
Views: 186
3 Shaky Dave Recovery
Last Post: SHAKY DAVE
Posted On: 2 Hours Ago
Replies: 57
Views: 8,306
0 gas cap
Last Post: sportsterpaul
Posted On: 2 Hours Ago
Replies: 6
Views: 293
0 Charging cell phone when camping?
Last Post: Folkie
Posted On: 2 Hours Ago
Replies: 65
Views: 18,973
0 Buy A new battery
Last Post: denguy
Posted On: 2 Hours Ago
Replies: 8
Views: 252
5 What year is the most collectible Sportster.
Last Post: denguy
Posted On: 2 Hours Ago
Replies: 7
Views: 297
0 Keep & Kill
Last Post: Graywolf
Posted On: 3 Hours Ago
Replies: 14,362
Views: 806,325
0 Pictorial Essay, my town, Waterloo, Ontario
Last Post: rejeanprimeau
Posted On: 3 Hours Ago
Replies: 20
Views: 4,322
0 Daily updates by email not working
Last Post: billeuze
Posted On: 3 Hours Ago
Replies: 9
Views: 211
0 Crusty's Travels
Last Post: SonWon
Posted On: 3 Hours Ago
Replies: 2,606
Views: 345,361
14 TC 88A Chat
Last Post: rejeanprimeau
Posted On: 3 Hours Ago
Replies: 784
Views: 50,499
0 This is gonna hurt.
Last Post: BWP 5p
Posted On: 3 Hours Ago
Replies: 7,827
Views: 1,582,717
0 sportster and a grand
Last Post: Maxeffort
Posted On: 3 Hours Ago
Replies: 11
Views: 176
0 Food porn
Last Post: Graywolf
Posted On: 4 Hours Ago
Replies: 1,681
Views: 293,881
0 Anyone hunting an XLCH in a Norton Featherbed Project?
Last Post: Ferrous Head
Posted On: 4 Hours Ago
Replies: 49
Views: 2,565
0 Hot Chicks on Hot Bikes
Last Post: Stairman
Posted On: 5 Hours Ago
Replies: 10,401
Views: 1,824,601
0 We were robbed at gun-point...
Last Post: sportsterpaul
Posted On: 6 Hours Ago
Replies: 33
Views: 2,124
0 Electric Harley sub-forum(s)...?
Last Post: NLXL
Posted On: 7 Hours Ago
Replies: 3
Views: 95
0 Roads I'd like to ride.
Last Post: Stairman
Posted On: 8 Hours Ago
Replies: 2,589
Views: 221,174
More...
Members Birthdays
gp9739 (75), danbango (72), andyman1958 (61), 55 Jr (58), Love2FixIt (50), keywan (48), C Dubya (45), CA71xlch (44)
Sponsored Links
Reply
 
Share Thread Tools Display Modes
  #1  
Old 11th March 2007
Gone Gone is offline
Banned
 
Join Date: Nov 2004
Posts: 165
Reputation: 26
Gone is an unknown quantity at this point
Default clutch adjustment

how do i adjust the clutch on my 06 sportster
Reply With Quote
  #2  
Old 11th March 2007
Matt Matt is offline
Riding with Angels
 
Join Date: Mar 2006
Location: Atl/StnMtn
Posts: 1,960
Sportster/Buell Model: XLCH
Sportster/Buell Year: 1968
Reputation: 2562
Matt is a jewel in the roughMatt is a jewel in the roughMatt is a jewel in the roughMatt is a jewel in the roughMatt is a jewel in the roughMatt is a jewel in the roughMatt is a jewel in the roughMatt is a jewel in the roughMatt is a jewel in the roughMatt is a jewel in the roughMatt is a jewel in the rough
Default

Get the factory manual and save lots of grief! If you do it you'll know it's right. If somebody else does all you can do is hope.
Matt
Reply With Quote
  #3  
Old 11th March 2007
cjburr's Avatar
cjburr cjburr is offline
Master Custom Bike Builder
 
Join Date: Sep 2005
Posts: 3,300
Sportster/Buell Model: Sportster 883/1250 Stage3
Sportster/Buell Year: 2006
Sportster/Buell Model #2: Buell S1 White Lightning
Sportster/Buell Year #2: 1998
Other Motorcycle Model: BMW K1300S
Other Motorcycle Year: 2009
Reputation: 5821
cjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nice
Default

I'll be doing mine shortly on my 06, I'll take some pics for you
__________________
My Other Toy Goes Mach 25
Reply With Quote
  #4  
Old 11th March 2007
cjburr's Avatar
cjburr cjburr is offline
Master Custom Bike Builder
 
Join Date: Sep 2005
Posts: 3,300
Sportster/Buell Model: Sportster 883/1250 Stage3
Sportster/Buell Year: 2006
Sportster/Buell Model #2: Buell S1 White Lightning
Sportster/Buell Year #2: 1998
Other Motorcycle Model: BMW K1300S
Other Motorcycle Year: 2009
Reputation: 5821
cjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nice
Default Clutch Adjustment

Adjusted my clutch today and took some pics along the way, hope this helps you out. It's a very simple task that will only take a 1/2 hour or less if you have the proper tools.

First thing to do is place the bike upright on a lift so when you remove the clutch inspection cover you don't lose any fluid, if you don't have a lift you need to have someone sit on the bike and hold it upright. The job doesn't take that long so it's not that big of a deal and they don't have to hold it up until you get to the part where you remove the inspection cover.

Remove the left side peg, unless you have forward controls.



Next pop off the spring type retaining clips so you can easily work on the cable.



Pull the rubber boot up to give access to the adjustment on the cable.



Break the jam nut loose and screw it up to the top.



Screw the cable adjuster up against the jam nut.



This will give you lots of slop at the lever like this.



Next remove the clutch inspection cover. These screws take a T27 Torx bit, if you don't have one go to Sears and pick up a kit that has all the Torx bits in it. I was unable to find a T27 by itself and had to get the kit. If you don't use the right bit you will surely strip the screw head and then you have a new can of worms.



Heres the kit I got



Here is the inside, you can see the hex lockplate with the spring attached, if the spring stuck to your cover then the hex lockplate may be sitting there by itself or still attached to the spring, no big deal.



Remove the hex lockplate with the attached spring off of the adjusting screw assembly. You can see how it is slotted to prevent the adjusting screw from backing out.





Using a flat blade screwdriver turn the adjuster counterclockwise until you feel resistance. Then turn it back clockwise a 1/4 turn.



Reinstall the hex lockplate with the spring, turn the adjustment screw clockwise if you have to to line up the flats on the lockplate.

With the bike upright it would be a good time to check the fluid level also before you put the inspection cover back on. The fluid level should be just below the bottom edge of the inspection cover hole with the bike upright.

Reinstall the clutch inspection cover being careful not to dislodge the quadring (rubber seal) from the primary cover. If it comes off use a little bearing grease to hold it in place. Also make sure the spring seats in the cup on the back side of the inspection cover. (See Shu's post below)


Reinstall the screws with some blue LocTite, torquing to 84 to 108 INCH POUNDS

Say it with me now, LocTite is our friend



Adjust your cable by turning the adjuster away from the jam nut until you have 1/16" to 1/8" clearance between the ferrule and the lever housing. Pull the cable away from the housing to determine this. Lock down the jam nut, pull the rubber boot back over it, reinstall the spring clips, put on the peg assembly and you're done.



Unfortunately for me, after my clutch was adjusted properly, I have confirmed that it still slips when a heavy hand is applied at the throttle. So I'll be back with an install of the Barnett extra plate kit soon.

Hope this helps you out, and if you don't have one already, go get the manual. You really need it, at least for the torque specs for your fasteners.

Chris

Last edited by cjburr; 13th March 2007 at 11:31.. Reason: add a step
Reply With Quote
  #5  
Old 11th March 2007
Shu's Avatar
Shu Shu is offline
Super Moderator
 
Join Date: Nov 2004
Location: West Central Illinois
Posts: 6,810
Sportster/Buell Model: 883/1200C
Sportster/Buell Year: 2000
Other Motorcycle Model: Harley Heritage
Other Motorcycle Year: 2007
Reputation: 202172
Shu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant future
Default

Great write up Chris. Great pictures. I made it a sticky thread.

One thing to add is that if the spring on the hex plate is not attached, make certain it is not damaged. Also when re-installing the derby cover, make sure you get that spring back in recessed area in the center of the derby cover. Because if it is cocked, it'll snap that sping and the little pieces tend to get stuck in the stator.
__________________
Shu

GONE BUT NEVER FORGOTTEN
Screamin' Eagle 10:1 pistons
Stage 2 883 heads
Screamin' Eagle .497" cams
Screamin' Eagle Mikuni HSR42
Thunderheader
Forcewinder
Reply With Quote
  #6  
Old 11th March 2007
radar's Avatar
radar radar is offline
Flat Track Champion
 
Join Date: Nov 2004
Location: Elmira, NY
Posts: 629
Sportster/Buell Model: XL1200C
Sportster/Buell Year: 2005
Other Motorcycle Model: Road King Classic
Other Motorcycle Year: 2007
Reputation: 204
radar is on a distinguished roadradar is on a distinguished roadradar is on a distinguished road
Default

Nice writeup Chris!
__________________
My Best to all,
Walt.

2005 XL1200C
Black, Chrome, and Taxed
2007 RK Classic
Suede Blue/Black, stock 'till I blow it up
Reply With Quote
  #7  
Old 11th March 2007
cjburr's Avatar
cjburr cjburr is offline
Master Custom Bike Builder
 
Join Date: Sep 2005
Posts: 3,300
Sportster/Buell Model: Sportster 883/1250 Stage3
Sportster/Buell Year: 2006
Sportster/Buell Model #2: Buell S1 White Lightning
Sportster/Buell Year #2: 1998
Other Motorcycle Model: BMW K1300S
Other Motorcycle Year: 2009
Reputation: 5821
cjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nicecjburr is just really nice
Default

Quote:
Originally Posted by Shu View Post
Great write up Chris. Great pictures. I made it a sticky thread.

One thing to add is that if the spring on the hex plate is not attached, make certain it is not damaged. Also when re-installing the derby cover, make sure you get that spring back in recessed area in the center of the derby cover. Because if it is cocked, it'll snap that sping and the little pieces tend to get stuck in the stator.
Too true Mr. Shu, thank you, I also edited it to tell him to put the bike on a lift so it is upright and he shouldn't lose any fluid when he takes the inspection cover off.

With the bike upright it would be a good time to check the fluid level also. The fluid level should be just below the bottom edge of the inspection cover hole with the bike upright.

Last edited by cjburr; 11th March 2007 at 18:58..
Reply With Quote
  #8  
Old 11th March 2007
radar's Avatar
radar radar is offline
Flat Track Champion
 
Join Date: Nov 2004
Location: Elmira, NY
Posts: 629
Sportster/Buell Model: XL1200C
Sportster/Buell Year: 2005
Other Motorcycle Model: Road King Classic
Other Motorcycle Year: 2007
Reputation: 204
radar is on a distinguished roadradar is on a distinguished roadradar is on a distinguished road
Default

Another note: If you don't have a custom derby cover, mark the top screw hole for re-installation, so it won't leak. They sometimes get a little warped to conform to the primary cover.
Reply With Quote
  #9  
Old 13th March 2007
Shu's Avatar
Shu Shu is offline
Super Moderator
 
Join Date: Nov 2004
Location: West Central Illinois
Posts: 6,810
Sportster/Buell Model: 883/1200C
Sportster/Buell Year: 2000
Other Motorcycle Model: Harley Heritage
Other Motorcycle Year: 2007
Reputation: 202172
Shu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant futureShu has a brilliant future
Default

Quote:
Originally Posted by radar View Post
Another note: If you don't have a custom derby cover, mark the top screw hole for re-installation, so it won't leak. They sometimes get a little warped to conform to the primary cover.
The derby only goes on one way due to the clutch cable hump.
Reply With Quote
Sponsored Links
  #10  
Old 13th March 2007
radar's Avatar
radar radar is offline
Flat Track Champion
 
Join Date: Nov 2004
Location: Elmira, NY
Posts: 629
Sportster/Buell Model: XL1200C
Sportster/Buell Year: 2005
Other Motorcycle Model: Road King Classic
Other Motorcycle Year: 2007
Reputation: 204
radar is on a distinguished roadradar is on a distinguished roadradar is on a distinguished road
Default

Shu,
You're right, I was thinking of the BT covers.
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Sponsored Links
All times are GMT +1. The time now is 02:57.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
XL Forum® - Linson Media LLC