The Sportster and Buell Motorcycle Forum - The XLFORUM®
 

Go Back   The Sportster and Buell Motorcycle Forum - The XLFORUM® > SPORTSTER MOTORCYCLE & BUELL MOTORCYCLE FORUM - GENERAL DISCUSSION > DYNO Charts and Result
XLF Blogs XLF Arcade XLF Disclaimer/Privacy Statement/Terms Of Use

DYNO Charts and Result Post your dyno charts and results here.

Active Threads
0 XL883L 2006 coughing and backfiring
Last Post: sportsterdoc
Posted On: 13 Minutes Ago
Replies: 9
Views: 223
0 What did you do for your sporty Today?
Last Post: hammer6315
Posted On: 25 Minutes Ago
Replies: 5,629
Views: 667,162
0 FS: Stock HD Solo Seat
Last Post: wrkdWS6
Posted On: 57 Minutes Ago
Replies: 0
Views: 12
6 What gasket sealer goo do you like?
Last Post: 60Gunner
Posted On: 1 Hour Ago
Replies: 3
Views: 74
0 Bendix / Zenith questions
Last Post: smokey 2
Posted On: 1 Hour Ago
Replies: 4
Views: 145
0 S&S IST Ignition
Last Post: 60Gunner
Posted On: 1 Hour Ago
Replies: 2
Views: 40
3 Wtb, Wts, Wtt, Wtg (Ironhead)
Last Post: mitch500
Posted On: 1 Hour Ago
Replies: 60
Views: 206,242
0 Shock Length Increase And Ride Height Increase New Question.
Last Post: Folkie
Posted On: 1 Hour Ago
Replies: 28
Views: 29
0 Those little ways to personalize your bike...
Last Post: harley506d
Posted On: 1 Hour Ago
Replies: 16
Views: 1,378
0 Solo spring seat on 08 Nightster?
Last Post: Toejam503
Posted On: 1 Hour Ago
Replies: 8
Views: 357
0 Roads I'd like to ride.
Last Post: Stairman
Posted On: 1 Hour Ago
Replies: 996
Views: 61,695
0 Long commute
Last Post: Tony F.
Posted On: 2 Hours Ago
Replies: 20
Views: 1,094
0 timing troubles!
Last Post: needspeed
Posted On: 2 Hours Ago
Replies: 26
Views: 1,085
0 JACKHAMMER 570 Cams!
Last Post: aswracing
Posted On: 2 Hours Ago
Replies: 163
Views: 45,246
5 what are these holes used to do?sportster gas tank
Last Post: shanneba
Posted On: 2 Hours Ago
Replies: 2
Views: 48
0 ....1
Last Post: Graywolf
Posted On: 3 Hours Ago
Replies: 4,771
Views: 238,718
0 Official XL Forum Random Image Thread (NO NUDITY!)
Last Post: Graywolf
Posted On: 3 Hours Ago
Replies: 42,532
Views: 6,597,539
0 Hello from Tennessee
Last Post: oreocat1
Posted On: 3 Hours Ago
Replies: 10
Views: 222
0 Any K model guys interested in cam regrinding?
Last Post: Chuckthebeatertruck
Posted On: 4 Hours Ago
Replies: 147
Views: 12,238
14 Iconic Parts that say it's a Harley!
Last Post: Toejam503
Posted On: 5 Hours Ago
Replies: 30
Views: 2,633
0 Hottie of the day, no nudity.
Last Post: Stairman
Posted On: 5 Hours Ago
Replies: 9,621
Views: 802,829
0 Dyno Chart Reference: 1250 (all 1250 conversions: 883-1250, 1200-1250)
Last Post: Folkie
Posted On: 5 Hours Ago
Replies: 85
Views: 74,497
6 Secret photo"s of folkies loft
Last Post: DEEP DIVER
Posted On: 6 Hours Ago
Replies: 1,480
Views: 212,815
0 Iree's late night cafe
Last Post: sportytrace
Posted On: 7 Hours Ago
Replies: 1,008
Views: 106,656
0 It's stalkie's Birthday!
Last Post: stalkie
Posted On: 7 Hours Ago
Replies: 5
Views: 89
0 What Sort Of Sporty Have You Got?
Last Post: Folkie
Posted On: 10 Hours Ago
Replies: 1,067
Views: 285,316
0 Adapting an '97 rear fender to an 2000?
Last Post: Hippysmack
Posted On: 12 Hours Ago
Replies: 3
Views: 78
0 Your Favorite Style
Last Post: 83ironman
Posted On: 12 Hours Ago
Replies: 464
Views: 175,783
0 Official XLForum Poll: What kind of bars are you running?
Last Post: clif02
Posted On: 12 Hours Ago
Replies: 651
Views: 143,004
0 Horn and starter button stop working
Last Post: IXL2Relax
Posted On: 13 Hours Ago
Replies: 10
Views: 476
More...
Members Birthdays
Sponsored Links
Reply
 
Share Thread Tools Display Modes
  #81  
Old 18th November 2017
aswracing's Avatar
aswracing aswracing is offline
A Million Facts & Figures
 
Join Date: Jan 2005
Location: Famous Potatoes
Posts: 9,925
Sportster/Buell Model: XL883
Sportster/Buell Year: 2007
Sportster/Buell Model #2: Buell Cyclone
Sportster/Buell Year #2: 1999
Reputation: 2138856
aswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond repute
Default



2013 XL1200 Sportster owned by a valued HAMMER PERFORMANCE customer, equipped as follows.

Comments: This is effectively our 110+hp 883 conversion package as applied to a 1200, with one big difference: it still has the stock, unmodified throttle body. In our testing, a simple low-cost porting service on the stock throttle body is good for about 5 horsepower at this level. We're hoping to get our hands on it and find him some more power.
__________________
Click Here to Contact Me

Reply With Quote
Sponsored Links
  #82  
Old 6th May 2018
aswracing's Avatar
aswracing aswracing is offline
A Million Facts & Figures
 
Join Date: Jan 2005
Location: Famous Potatoes
Posts: 9,925
Sportster/Buell Model: XL883
Sportster/Buell Year: 2007
Sportster/Buell Model #2: Buell Cyclone
Sportster/Buell Year #2: 1999
Reputation: 2138856
aswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond repute
Default



1250 and 1275 conversions, done on the same bike with the same set of stock 883 heads, same Patriot exhaust, Powervision tuner, Dynojet dyno, etc.



Same 1250 & 1275 results, as compared to the same bike when it was a stock 883.
Reply With Quote
  #83  
Old 10th December 2018
aswracing's Avatar
aswracing aswracing is offline
A Million Facts & Figures
 
Join Date: Jan 2005
Location: Famous Potatoes
Posts: 9,925
Sportster/Buell Model: XL883
Sportster/Buell Year: 2007
Sportster/Buell Model #2: Buell Cyclone
Sportster/Buell Year #2: 1999
Reputation: 2138856
aswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond repute
Default



2007 XL883 equipped as follows:
  • Stock EFI 1200 heads
  • Stock original "W" cams
  • Air Hammer air cleaner (SLEDGE model)
  • Patriot exhaust
  • Dynojet Powervision tuner
  • tested on the same Dynojet 188 dynamometer

Blue: flat top 1275 kit
Red: flat top 1250 kit
Green: stock 1200 cylinders and flat top pistons

Comments: Through the bottom and middle, making the motor bigger adds a lot of torque and power. But as you go higher in rpm, the lines converge, and the big bore kit doesn't bring nearly as much to the party. Also notice how the bigger the motor, the lower the rpm at which the horsepower peaks.

That's typical of a motor that's had it's displacement increased without a corresponding increase in breathing. Making the motor bigger causes the air demand to go up. At low to mid rpm ranges, there's plenty of time to fill the cylinder, so the displacement increase brings a bunch more torque and thus power. But at high rpm, things are happening faster and faster, there's less time to fill the cylinder, and the motor becomes breathing constrained instead of displacement constrained.

So to get a big top side number with a big bore kit, you really need to do breathing mods as well (cams and/or head work).

However, for many people, the bottom to the mid range is more important anyway. So a lot of these kits get installed without cams and/or head work and the owner is perfectly happy with the results.
Reply With Quote
  #84  
Old 15 Hours Ago
aswracing's Avatar
aswracing aswracing is offline
A Million Facts & Figures
 
Join Date: Jan 2005
Location: Famous Potatoes
Posts: 9,925
Sportster/Buell Model: XL883
Sportster/Buell Year: 2007
Sportster/Buell Model #2: Buell Cyclone
Sportster/Buell Year #2: 1999
Reputation: 2138856
aswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond repute
Default



Today we tested the 1275 kit with the JACKHAMMER 570 Cams and got the above result.

Details: 2007 XL883 equipped as follows:
  • Stock EFI 1200 heads
  • Air Hammer air cleaner (SLEDGE model)
  • Patriot exhaust
  • Dynojet Powervision tuner
  • tested on the same Dynojet 188 dynamometer

Blue: flat top Flat Top 1275 kit and JACKHAMMER 570 Cams
Red: stock 1200 cylinders, stock 1200 flat top pistons, and stock "W" cams

These are the only changes between the two pulls, plus the EFI was remapped for each configuration.
Reply With Quote
  #85  
Old 13 Hours Ago
aswracing's Avatar
aswracing aswracing is offline
A Million Facts & Figures
 
Join Date: Jan 2005
Location: Famous Potatoes
Posts: 9,925
Sportster/Buell Model: XL883
Sportster/Buell Year: 2007
Sportster/Buell Model #2: Buell Cyclone
Sportster/Buell Year #2: 1999
Reputation: 2138856
aswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond repute
Default

We also tested the porting of the throttle body on this same result:



Blue is the ported throttle body
Red is the stock throttle body

This is result is pretty typical when we port a throttle body at this power level. 105ish hp is right on the cusp of where the stock throttle body starts becoming a significant restriction on the motor. Going up from here, it starts costing pretty significant power and you definitely want to address it.
Reply With Quote
  #86  
Old 5 Hours Ago
Folkie's Avatar
Folkie Folkie is offline
Brass Nut
 
Join Date: Feb 2005
Location: Western Weald
Posts: 44,865
Sportster/Buell Model: XL1200CB
Sportster/Buell Year: 2015
Other Motorcycle Model: CRF250L
Other Motorcycle Year: 2017
Reputation: 10565926
Folkie has a reputation beyond reputeFolkie has a reputation beyond reputeFolkie has a reputation beyond reputeFolkie has a reputation beyond reputeFolkie has a reputation beyond reputeFolkie has a reputation beyond reputeFolkie has a reputation beyond reputeFolkie has a reputation beyond reputeFolkie has a reputation beyond reputeFolkie has a reputation beyond reputeFolkie has a reputation beyond repute
Default

Just a reminder: posts with dyno charts only; no comments or chat here please. Other posts will be deleted. Comments and questions about the dyno charts posted here can be posted in a separate thread in the Dyno Charts And Results section. Thanks.
__________________
Folkie
Super Moderator
South East England Riders



There is nothing at the end of any road better than may be found beside it. Edward Thomas (1878 - 1917)
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 9 (0 members and 9 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Sponsored Links
All times are GMT +1. The time now is 17:59.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
XL Forum® - Linson Media LLC