The Sportster and Buell Motorcycle Forum - The XLFORUM®
 

Go Back   The Sportster and Buell Motorcycle Forum - The XLFORUM® > SPORTSTER MOTORCYCLE FORUM > Sportster Motorcycle Era Specific and Model Specific > Ironhead Sportster Motorcycle Talk (1957-1985)
XLF Blogs XLF Arcade XLF Disclaimer/Privacy Statement/Terms Of Use

Notices

Ironhead Sportster Motorcycle Talk (1957-1985) For all those that wanna talk about Ironhead Sportster Motorcycles

Active Threads
0 Hottie of the day, no nudity.
Last Post: cal43
Posted On: 3 Minutes Ago
Replies: 26,150
Views: 2,687,582
0 Hot Rods, Rat Rods, and Customs.
Last Post: cal43
Posted On: 4 Minutes Ago
Replies: 4,379
Views: 668,974
0 Official XL Forum Random Image Thread (NO NUDITY!)
Last Post: cal43
Posted On: 6 Minutes Ago
Replies: 49,505
Views: 8,056,507
0 Hot Chicks on Hot Bikes
Last Post: cal43
Posted On: 8 Minutes Ago
Replies: 11,590
Views: 2,374,825
7 1983 Ironhead motor in a 1996 EVO frame?
Last Post: ryder rick
Posted On: 1 Hour Ago
Replies: 37
Views: 3,751
0 Corona Virus
Last Post: iNSaNeSHaNe
Posted On: 1 Hour Ago
Replies: 1,032
Views: 99,048
0 New sportster in HD Research Survey
Last Post: Mr Dream Merchant
Posted On: 3 Hours Ago
Replies: 88
Views: 7,365
0 2021 HDs now Out!
Last Post: Mr Dream Merchant
Posted On: 4 Hours Ago
Replies: 9
Views: 338
0 Cutting out at WOT
Last Post: IXL2Relax
Posted On: 4 Hours Ago
Replies: 8
Views: 118
0 Scrambler, Dirtster, Dual Sport , Adventure Sportster picture thread
Last Post: phyhowe
Posted On: 4 Hours Ago
Replies: 112
Views: 93,662
0 Should I apolgise to Harley Davidson ?
Last Post: Ferrous Head
Posted On: 4 Hours Ago
Replies: 74
Views: 6,406
0 Can I fill gas tank up to top?
Last Post: BKB
Posted On: 5 Hours Ago
Replies: 2
Views: 67
0 1977 Shift shaft
Last Post: IronMick
Posted On: 5 Hours Ago
Replies: 2
Views: 105
0 Zippers Hammer 99 kit Info
Last Post: rocketmangb
Posted On: 5 Hours Ago
Replies: 2
Views: 108
0 did .you ever kick a good man when he,, was down
Last Post: 11B40
Posted On: 5 Hours Ago
Replies: 12
Views: 799
0 Mimi the Deerslayer: the triple threat
Last Post: madnss
Posted On: 5 Hours Ago
Replies: 9
Views: 303
0 Mid West Meet & Greet
Last Post: skien
Posted On: 5 Hours Ago
Replies: 832
Views: 82,179
0 83 XLH w/Velorex 562
Last Post: ferretface
Posted On: 6 Hours Ago
Replies: 3
Views: 88
0 Motorcycle airbag jeans
Last Post: IXL2Relax
Posted On: 7 Hours Ago
Replies: 12
Views: 388
0 Reflectors...Yeah, or Neh
Last Post: Marsikus
Posted On: 7 Hours Ago
Replies: 187
Views: 47,150
0 Boardtracker Project
Last Post: JonesL
Posted On: 9 Hours Ago
Replies: 652
Views: 133,875
0 Flat Tracker Pics
Last Post: Steve9
Posted On: 9 Hours Ago
Replies: 1,172
Views: 654,892
5 Tire Pressure?
Last Post: Iron Mike
Posted On: 10 Hours Ago
Replies: 49
Views: 5,607
0 Battery
Last Post: oldboy
Posted On: 10 Hours Ago
Replies: 6
Views: 184
0 XL1200 03 changing from 29tooth to 27
Last Post: jkinkade
Posted On: 10 Hours Ago
Replies: 14
Views: 1,061
0 2021s getting new MT22 ECM
Last Post: 60Gunner
Posted On: 10 Hours Ago
Replies: 0
Views: 63
0 Rear Sprocket Runout
Last Post: Tim The Grim
Posted On: 10 Hours Ago
Replies: 1
Views: 77
0 This is gonna hurt.
Last Post: Graywolf
Posted On: 10 Hours Ago
Replies: 8,231
Views: 1,788,497
0 75 IH Oil leaking into starter from primary side/ bendix
Last Post: rokytnji
Posted On: 11 Hours Ago
Replies: 12
Views: 442
0 Improving Fuel Mileage
Last Post: LLOYD883
Posted On: 11 Hours Ago
Replies: 20
Views: 471
More...
Members Birthdays
Reynoldston (80), showmebandit (67), Hoppy1313 (67), FredrikK (65), Toejam503 (65), YO MUDA (62), Altopass (61), tim 2007xl1200c (54), w9awx (48), 3xtrastout (42)
Reply
 
Share Thread Tools Display Modes
  #11  
Old 1 Week Ago
Jaime1840 Jaime1840 is offline
Biker
 
Join Date: Dec 2019
Posts: 55
Sportster/Buell Model: 883 low
Sportster/Buell Year: 2006
Reputation: 10
Jaime1840 is an unknown quantity at this point
Default

Quote:
Originally Posted by ryder rick View Post
What year cases?
I think 84 & 85 had a needle bearing
Hey rider rick,

The cases are from 1974.
Reply With Quote
  #12  
Old 1 Week Ago
Jaime1840 Jaime1840 is offline
Biker
 
Join Date: Dec 2019
Posts: 55
Sportster/Buell Model: 883 low
Sportster/Buell Year: 2006
Reputation: 10
Jaime1840 is an unknown quantity at this point
Default

Quote:
Originally Posted by IronMick View Post
Sorry. What I see in the link is no picture of the parts you were discussing, only some advertisements, some of which I would not show my children
Hey Ironmick,

I don´t know man, when I click on it there is no advertisements, just the picture of the thread Im talking about.

cheers
Reply With Quote
  #13  
Old 1 Week Ago
IronMick's Avatar
IronMick IronMick is offline
Rider Of The Iron Steed
 
Join Date: Dec 2003
Location: London, ON Canada
Posts: 32,523
Sportster/Buell Model: XLH
Sportster/Buell Year: 1978
Reputation: 1280341
IronMick has a reputation beyond reputeIronMick has a reputation beyond reputeIronMick has a reputation beyond reputeIronMick has a reputation beyond reputeIronMick has a reputation beyond reputeIronMick has a reputation beyond reputeIronMick has a reputation beyond reputeIronMick has a reputation beyond reputeIronMick has a reputation beyond reputeIronMick has a reputation beyond reputeIronMick has a reputation beyond repute
Default

Quote:
Originally Posted by Jaime1840 View Post
Hey Ironmick,

I don´t know man, when I click on it there is no advertisements, just the picture of the thread Im talking about.

cheers
These things happen from time to time, depending of what site the pic is hosted on, the geographical location of the people, the type of membership [privacy, advertisement policies, etc] - whatever. The Google, Amazon, Microsoft, Facebook etc mess of rules designed to make them more money, especially from adult advertising
__________________
Mick
IronHead Forever!

Visit Mick's WebSite
[And Check Out My Autobiog]
Reply With Quote
  #14  
Old 1 Week Ago
needspeed needspeed is offline
XL FORUM LIFE MEMBER
 
Join Date: May 2014
Posts: 1,342
Sportster/Buell Model: xlh
Sportster/Buell Year: 1974
Reputation: 951510
needspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond repute
Default

Your mainshaft bearing isn't a Harley upgrade. It's a modification that someone before you did. If it was done properly I think it should work adequately and I see no need to change it.

It's hard to find a needle bearing that works with the diameter of the mainshaft.

A stock mainshaft measures .991".
An inch series bearing for a 1 inch shaft would be too big.
A metric bearing for a 25mm shaft (.984") is too small.

There is a modification that some have done where the stock rollers are replaced with a 25mm I.D. ball bearing. In which case the shaft has to be ground smaller to fit.

It's possible that was done to your shaft too. If it doesn't measure .991" then that is the case.

If there are numbers on the bearing would you post them?
Reply With Quote
  #15  
Old 1 Week Ago
Jaime1840 Jaime1840 is offline
Biker
 
Join Date: Dec 2019
Posts: 55
Sportster/Buell Model: 883 low
Sportster/Buell Year: 2006
Reputation: 10
Jaime1840 is an unknown quantity at this point
Default

Quote:
Originally Posted by needspeed View Post
Your mainshaft bearing isn't a Harley upgrade. It's a modification that someone before you did. If it was done properly I think it should work adequately and I see no need to change it.

It's hard to find a needle bearing that works with the diameter of the mainshaft.

A stock mainshaft measures .991".
An inch series bearing for a 1 inch shaft would be too big.
A metric bearing for a 25mm shaft (.984") is too small.

There is a modification that some have done where the stock rollers are replaced with a 25mm I.D. ball bearing. In which case the shaft has to be ground smaller to fit.

It's possible that was done to your shaft too. If it doesn't measure .991" then that is the case.

If there are numbers on the bearing would you post them?
Hey needspeed,

Thanks for the info,

I'm going to measure the shaft today and I will check if there's any numbers on the bearing and I will let you know.

Jaime
Reply With Quote
  #16  
Old 1 Week Ago
Jaime1840 Jaime1840 is offline
Biker
 
Join Date: Dec 2019
Posts: 55
Sportster/Buell Model: 883 low
Sportster/Buell Year: 2006
Reputation: 10
Jaime1840 is an unknown quantity at this point
Default

Quote:
Originally Posted by needspeed View Post
Your mainshaft bearing isn't a Harley upgrade. It's a modification that someone before you did. If it was done properly I think it should work adequately and I see no need to change it.

It's hard to find a needle bearing that works with the diameter of the mainshaft.

A stock mainshaft measures .991".
An inch series bearing for a 1 inch shaft would be too big.
A metric bearing for a 25mm shaft (.984") is too small.

There is a modification that some have done where the stock rollers are replaced with a 25mm I.D. ball bearing. In which case the shaft has to be ground smaller to fit.

It's possible that was done to your shaft too. If it doesn't measure .991" then that is the case.

If there are numbers on the bearing would you post them?
Hey man,

The mainshaft has been grounded off, It measures .944" but I dont think it was done properly, it looks like it was done by hand with sand paper or something... surprisingly the bearing fits pretty good both in the shaft and in the case. I bought another transmission a while ago because the one that came with the bike was in very bad condition and it was more expensive to repair it than to buy a complete used one, my idea is to keep this bearing set up and machine the mainshaft of the new gearbox in a machine shop. What do you think? by the way there was no numbers on the bearing.

Here is some pictures:

https://postimg.cc/gallery/1RNfpKT
Reply With Quote
  #17  
Old 1 Week Ago
ryder rick's Avatar
ryder rick ryder rick is offline
Senior Master Custom Bike Builder
 
Join Date: Jun 2008
Location: Cornelius, OR
Posts: 9,514
Reputation: 1114996
ryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond repute
Default

My calibrated eyeball micrometer says, That bearing does not look big enough to go on the top shaft....?
__________________
Ryder Rick "I know right from wrong, but sometimes, wrong feels right"
Reply With Quote
  #18  
Old 1 Week Ago
needspeed needspeed is offline
XL FORUM LIFE MEMBER
 
Join Date: May 2014
Posts: 1,342
Sportster/Buell Model: xlh
Sportster/Buell Year: 1974
Reputation: 951510
needspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond reputeneedspeed has a reputation beyond repute
Default

I'm assuming the bearing you're using came with an outer and inner race.

The OD of the STOCK race is about 1.564". So if the steel insert in the case was bored any bigger than that to fit your bearing, it will be difficult to change back to the stock set up. Keeping what you have is probably the easiest thing to do.

I'm not a bearing expert but I don't think your bearing can handle the load that the stock rollers can, but I think that it's good enough.

Looks like the sprocket is what keeps the bearing from sliding out to the right. What do the mainshaft shims ride against? Is there a steel shoulder like stock?

Your bearing has an inner race so the surface finish of the shaft where it's turned down is not an issue, but it needs to run concentric with the shaft and be a reasonably close fit in the bearing. At the .944 diameter I doubt that all the case hardening is gone and that shouldn't matter either.

In post #16, Picture brng3 it looks like the roller cage is cracked.
Reply With Quote
  #19  
Old 1 Week Ago
ryder rick's Avatar
ryder rick ryder rick is offline
Senior Master Custom Bike Builder
 
Join Date: Jun 2008
Location: Cornelius, OR
Posts: 9,514
Reputation: 1114996
ryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond reputeryder rick has a reputation beyond repute
Default

I take that back, It does fit, it appears to have a inner race maybe there is also one in the outer position? Any numbers on anything?
Reply With Quote
  #20  
Old 2 Days Ago
Jaime1840 Jaime1840 is offline
Biker
 
Join Date: Dec 2019
Posts: 55
Sportster/Buell Model: 883 low
Sportster/Buell Year: 2006
Reputation: 10
Jaime1840 is an unknown quantity at this point
Default

Quote:
Originally Posted by needspeed View Post
I'm assuming the bearing you're using came with an outer and inner race.

The OD of the STOCK race is about 1.564". So if the steel insert in the case was bored any bigger than that to fit your bearing, it will be difficult to change back to the stock set up. Keeping what you have is probably the easiest thing to do.

I'm not a bearing expert but I don't think your bearing can handle the load that the stock rollers can, but I think that it's good enough.

Looks like the sprocket is what keeps the bearing from sliding out to the right. What do the mainshaft shims ride against? Is there a steel shoulder like stock?

Your bearing has an inner race so the surface finish of the shaft where it's turned down is not an issue, but it needs to run concentric with the shaft and be a reasonably close fit in the bearing. At the .944 diameter I doubt that all the case hardening is gone and that shouldn't matter either.

In post #16, Picture brng3 it looks like the roller cage is cracked.
Hopefully I will have time to check everything this weekend! thanks
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT +1. The time now is 09:13.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
XL Forum® - Linson Media LLC