The Sportster and Buell Motorcycle Forum - The XLFORUM®
 

Go Back   The Sportster and Buell Motorcycle Forum - The XLFORUM® > SPORTSTER MOTORCYCLE FORUM > Sportster Motorcycle Era Specific and Model Specific > Ironhead Sportster Motorcycle Talk (1957-1985)
XLF Blogs XLF Arcade XLF Disclaimer/Privacy Statement/Terms Of Use

Notices

Ironhead Sportster Motorcycle Talk (1957-1985) For all those that wanna talk about Ironhead Sportster Motorcycles

Active Threads
0 Who's still riding???
Last Post: SLW210
Posted On: 2 Minutes Ago
Replies: 41
Views: 1,644
0 no introduction needed
Last Post: Nibelungen
Posted On: 3 Minutes Ago
Replies: 0
Views: 4
0 This week on Craig's list
Last Post: 60weight
Posted On: 6 Minutes Ago
Replies: 3,627
Views: 373,123
0 Where do you ride in the lane?
Last Post: SLW210
Posted On: 11 Minutes Ago
Replies: 51
Views: 4,141
0 Royal Enfield V-twin concept at EICMA show
Last Post: DEEP DIVER
Posted On: 11 Minutes Ago
Replies: 5
Views: 100
0 I've been getting some revenge.
Last Post: DEEP DIVER
Posted On: 13 Minutes Ago
Replies: 1
Views: 22
0 Official XL Forum Random Image Thread (NO NUDITY!)
Last Post: Stairman
Posted On: 20 Minutes Ago
Replies: 41,998
Views: 6,499,948
0 Chardhin moved to Pennsylvania!
Last Post: lostNdallas
Posted On: 29 Minutes Ago
Replies: 2
Views: 39
0 inlet rubber band available by the meter?
Last Post: paulc
Posted On: 1 Hour Ago
Replies: 27
Views: 1,035
0 Shinko Tyre update - long and boring.
Last Post: slamtry
Posted On: 1 Hour Ago
Replies: 19
Views: 4,934
0 This is gonna hurt.
Last Post: Four Speed
Posted On: 1 Hour Ago
Replies: 7,569
Views: 1,417,781
0 Who is at fault here? (WARNING - GRAPHIC!)
Last Post: SLW210
Posted On: 1 Hour Ago
Replies: 142
Views: 32,320
0 Got New Bike - 2002 Sportster Project
Last Post: mzavala2424
Posted On: 2 Hours Ago
Replies: 14
Views: 248
0 Poll for the legalization of cannabis
Last Post: ed_in_az
Posted On: 2 Hours Ago
Replies: 424
Views: 54,983
0 After 13 Years, Brake Improvements
Last Post: SLW210
Posted On: 2 Hours Ago
Replies: 16
Views: 546
0 primary and gear case cover paint.
Last Post: newroadster
Posted On: 3 Hours Ago
Replies: 0
Views: 40
0 Hi from the Netherlands
Last Post: Dutch_Bobber
Posted On: 3 Hours Ago
Replies: 19
Views: 357
0 What riding gear do you have/wear in good and/or poor weather?
Last Post: SLW210
Posted On: 3 Hours Ago
Replies: 105
Views: 32,679
0 Compressor tool
Last Post: rocketmangb
Posted On: 4 Hours Ago
Replies: 1
Views: 63
0 Sportster Primary / Transmission oil analysis
Last Post: shanneba
Posted On: 4 Hours Ago
Replies: 26
Views: 3,345
0 Thinking about restoring my '65 XLCH forks to stock
Last Post: Sprtstr1200s
Posted On: 4 Hours Ago
Replies: 15
Views: 414
0 burrs & grooves in clutch basket
Last Post: sportsterpaul
Posted On: 5 Hours Ago
Replies: 39
Views: 1,101
0 Joe Minton article on HSR 42 tuning
Last Post: jordan1200
Posted On: 5 Hours Ago
Replies: 13
Views: 3,250
0 Anybody Collect Dealer Logo'd Harley T-Shirts?
Last Post: mikeLI_77
Posted On: 6 Hours Ago
Replies: 127
Views: 19,148
0 FLH saddlebags on Easy Brackets
Last Post: Screw Loose Dan
Posted On: 7 Hours Ago
Replies: 11
Views: 275
0 cancer
Last Post: Nibelungen
Posted On: 8 Hours Ago
Replies: 581
Views: 59,983
0 Moto Guzzi V9 Bobber debut
Last Post: Bone
Posted On: 8 Hours Ago
Replies: 41
Views: 2,526
0 Ice tire
Last Post: DEEP DIVER
Posted On: 9 Hours Ago
Replies: 1
Views: 65
0 Hottie of the day, no nudity.
Last Post: Stairman
Posted On: 9 Hours Ago
Replies: 8,722
Views: 719,478
More...
Members Birthdays
Sponsored Links
Reply
 
Share Thread Tools Display Modes
  #51  
Old 29th July 2018
nychopper nychopper is offline
Biker
 
Join Date: Apr 2018
Posts: 30
Sportster/Buell Model: ironhead
Sportster/Buell Year: 77
Reputation: 10
nychopper is an unknown quantity at this point
Default

Quote:
Originally Posted by IronMick View Post
I have not heard of this before, certainly not as a general principle or something to be expected.

I have had three head gasket leaks...
One was extremely obvious by the loud, squeaky sound of air escaping thru the space, in this video...

Head Gasket Leak


This was caused by some very bad machine shop work done to prepare that cylinder head for dual plugging. It was done by a shop that I should have been able to trust. My bad mistake

The second was a very interesting mystery. The leak was exactly adjacent to one of the oil drain holes, and on the inside edge of the hole. So the leak was entirely contained within the head. I really did not discover it until I had the head off. If I recall correctly there was excessive oil consumption or some other symptom, but I did not suspect a head gasket leak until I removed the head for whatever reason.

BTW, never clean up the oil on the cylinder head, gasket or on the cylinder itself before bringing it to a machine shop or other for examination. The oil etc patterns contain important information.

The third was the brother to #2 - the leak was adjacent to the oil hole, but on the outside. No air leakage sound like #1, but there was actual oil leakage - which is rare in head gasket leaks since the oil holes are such a small % of the leakable area.

This one required extra work because the head gasket is directly behind the middle pushrod tube seal. So that had to be eliminated as a possible source of the leak before calling it a gasket leak. For this I made a sandwich of two slices of paper towel with a slice of aluminum foil between. I stuffed that between the cylinder/cylinder head and the pushrod tube.

The oil migrated around between the fins and appeared on the cylinder side of the sandwich.

QED

I appreciate this! Well i think I'm throwing in the towel and bringing it to a shop. This is beyond me at this point haha.

thanks for all the help everybody! I'll update when I hear back from the shop
Reply With Quote
  #52  
Old 30th July 2018
wedge's Avatar
wedge wedge is offline
XL FORUM TEAM MEMBER
 
Join Date: Jun 2010
Posts: 10,908
Sportster/Buell Model: 1200R
Sportster/Buell Year: 2005
Other Motorcycle Model: 5 bikes and 1 quad
Reputation: 3018779
wedge has a reputation beyond reputewedge has a reputation beyond reputewedge has a reputation beyond reputewedge has a reputation beyond reputewedge has a reputation beyond reputewedge has a reputation beyond reputewedge has a reputation beyond reputewedge has a reputation beyond reputewedge has a reputation beyond reputewedge has a reputation beyond reputewedge has a reputation beyond repute
Default

You didn't even pull the heads yet according to the posts I see. Why would you give up before starting? It's not rocket science, it's just top end work, and you have the entire forum here ready to help as you go about it.
__________________
A Biker is not just any guy who rides... that's a motorist.
A guy that gets up and rides again after every crash... that's a Biker.

Whitworth Fork Brace: http://xlforum.net/forums/m...outme&simple=1
Reply With Quote
  #53  
Old 30th July 2018
ezmerf's Avatar
ezmerf ezmerf is offline
Senior Master Custom Bike Builder
 
Join Date: Jul 2010
Location: Booneville,Ms.
Posts: 4,246
Sportster/Buell Model: XLCH
Sportster/Buell Year: 1974
Sportster/Buell Model #2: XLS
Sportster/Buell Year #2: 1980
Blog Entries: 1
Reputation: 53828
ezmerf is a splendid one to beholdezmerf is a splendid one to beholdezmerf is a splendid one to beholdezmerf is a splendid one to beholdezmerf is a splendid one to beholdezmerf is a splendid one to beholdezmerf is a splendid one to beholdezmerf is a splendid one to beholdezmerf is a splendid one to beholdezmerf is a splendid one to beholdezmerf is a splendid one to behold
Default

Also most part houses loan tools if you don't have what it takes.
__________________
Murphy's Law :vvet:
Reply With Quote
  #54  
Old 17th August 2018
GA_Ironhead GA_Ironhead is offline
Senior Master Custom Bike Builder
 
Join Date: Mar 2006
Location: Athens, GA
Posts: 4,773
Sportster/Buell Model: XLCH
Sportster/Buell Year: 1962
Reputation: 73212
GA_Ironhead has much to be proud ofGA_Ironhead has much to be proud ofGA_Ironhead has much to be proud ofGA_Ironhead has much to be proud ofGA_Ironhead has much to be proud ofGA_Ironhead has much to be proud ofGA_Ironhead has much to be proud ofGA_Ironhead has much to be proud ofGA_Ironhead has much to be proud ofGA_Ironhead has much to be proud ofGA_Ironhead has much to be proud of
Default

Any updates?
__________________
If you want to do something, you’ll find a way. If you don’t, you’ll find an excuse.
Reply With Quote
Sponsored Links
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Sponsored Links
All times are GMT +1. The time now is 20:58.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
XL Forum® - Linson Media LLC