The Sportster and Buell Motorcycle Forum - The XLFORUM®
 

Go Back   The Sportster and Buell Motorcycle Forum - The XLFORUM® > BUELL MOTORCYCLE FORUM > Buell Motorcycle Top End
XLF Blogs XLF Arcade XLF Disclaimer/Privacy Statement/Terms Of Use

Notices

Active Threads
0 RIDE REPORT During Covid, 13 States & Some Spectacular Riding
Last Post: DK Custom
Posted On: 5 Minutes Ago
Replies: 4
Views: 198
0 Mikuni - hangin revs
Last Post: Piccollob12
Posted On: 15 Minutes Ago
Replies: 3
Views: 46
0 Starter for an XLCH
Last Post: Imaginearat
Posted On: 31 Minutes Ago
Replies: 9
Views: 173
0 79-85 Breather Vent Mod - Adding a Secondary Vent Hose at 6:00 Position
Last Post: needspeed
Posted On: 31 Minutes Ago
Replies: 101
Views: 3,028
0 Xl???
Last Post: 1200CustomHD
Posted On: 37 Minutes Ago
Replies: 19
Views: 469
0 Hello from LA area
Last Post: initiatebjj
Posted On: 39 Minutes Ago
Replies: 9
Views: 145
0 so it's officially ended
Last Post: NLXL
Posted On: 1 Hour Ago
Replies: 54
Views: 2,518
0 Oil not returning to tank
Last Post: 1Scooter
Posted On: 1 Hour Ago
Replies: 1
Views: 62
0 Range With Carby 4.5 Gal Tank
Last Post: Nicktater
Posted On: 1 Hour Ago
Replies: 113
Views: 55,926
0 Hottie of the day, no nudity.
Last Post: trainman
Posted On: 1 Hour Ago
Replies: 22,316
Views: 2,283,133
0 99 1200S Sport Ignition Troubleshooting
Last Post: IXL2Relax
Posted On: 2 Hours Ago
Replies: 31
Views: 1,033
0 Mikuni VM-38 bogs in cool weather
Last Post: The Doctor71
Posted On: 2 Hours Ago
Replies: 15
Views: 448
0 Keep & Kill
Last Post: Graywolf
Posted On: 2 Hours Ago
Replies: 18,153
Views: 1,072,668
0 blocked main jet air bleed screw
Last Post: RussW
Posted On: 2 Hours Ago
Replies: 2
Views: 62
0 old parts
Last Post: bill smith
Posted On: 2 Hours Ago
Replies: 15
Views: 512
0 How to remove Bendix float bowl?
Last Post: Greasyman
Posted On: 3 Hours Ago
Replies: 0
Views: 32
0 Rear head removal on 77 Sportster
Last Post: brucstoudt
Posted On: 3 Hours Ago
Replies: 17
Views: 505
0 1972 Build thread please subscribe
Last Post: brucstoudt
Posted On: 3 Hours Ago
Replies: 96
Views: 8,613
0 Now I did it. Feel my pain
Last Post: motorfish
Posted On: 3 Hours Ago
Replies: 2
Views: 119
0 Xr750
Last Post: seajay
Posted On: 5 Hours Ago
Replies: 1
Views: 70
3 Wtb, Wts, Wtt, Wtg (Evos)
Last Post: Randy_rots
Posted On: 5 Hours Ago
Replies: 14
Views: 80,748
0 PLEASE READ THIS Before You Post In 'The BUY - SELL - TRADE Zone'!
Last Post: Folkie
Posted On: 5 Hours Ago
Replies: 1
Views: 154
0 Runs great - stalls on clutch pull
Last Post: tedcool
Posted On: 5 Hours Ago
Replies: 8
Views: 260
3 Wtb, Wts, Wtt, Wtg (Ironhead)
Last Post: rivethog
Posted On: 5 Hours Ago
Replies: 51
Views: 265,145
0 Food porn
Last Post: Stairman
Posted On: 6 Hours Ago
Replies: 2,096
Views: 414,614
0 Compression tool for working on springer front ends?
Last Post: FiftySixer
Posted On: 7 Hours Ago
Replies: 8
Views: 697
0 Help me identify this washer
Last Post: GA_Ironhead
Posted On: 7 Hours Ago
Replies: 2
Views: 114
0 100 vs 110 front tire
Last Post: Steve9
Posted On: 8 Hours Ago
Replies: 125
Views: 75,863
0 Sportster drag bike
Last Post: rejeanprimeau
Posted On: 9 Hours Ago
Replies: 1
Views: 113
0 Curious question on E85
Last Post: Nicktater
Posted On: 9 Hours Ago
Replies: 6
Views: 381
More...
Members Birthdays
texrex (68), jjluvstoride (55), luisbmns (50), njstoehr (44), tacho75xlh (41), 80ironhead80 (31), Xttrackerr (25)
Reply
 
Share Thread Tools Display Modes
  #11  
Old 28th May 2019
60Gunner's Avatar
60Gunner 60Gunner is offline
Senior Custom Bike Builder
 
Join Date: Sep 2017
Location: United States
Posts: 2,940
Sportster/Buell Model: 1200/1250C
Sportster/Buell Year: 05
Reputation: 3247009
60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute
Default

Quote:
Originally Posted by Sprtstr1200s View Post
I don't know what shape my springs are in. Haven't opened the motor yet.
Your stock ones were just weaker to begin with. Fine til you start putting cams in.
Reply With Quote
  #12  
Old 28th May 2019
Sprtstr1200s's Avatar
Sprtstr1200s Sprtstr1200s is offline
XL FORUM TEAM MEMBER
 
Join Date: Aug 2016
Location: Space Coast
Posts: 811
Sportster/Buell Model: Sportster XL1200s
Sportster/Buell Year: 1999
Reputation: 559600
Sprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond repute
Default

Spent an weekend screwing around testing springs, new, old. Amazed at the variations. https://www.bing.com/images/search?q...ster&FORM=IGRE
Reply With Quote
  #13  
Old 29th May 2019
ParrotHead's Avatar
ParrotHead ParrotHead is offline
XL FORUM TEAM MEMBER
 
Join Date: Aug 2006
Location: Near Philly
Posts: 7,965
Sportster/Buell Model: 1200R
Sportster/Buell Year: 2006
Sportster/Buell Model #2: 1200R
Sportster/Buell Year #2: 2007
Other Motorcycle Model: Suzuki GT550
Other Motorcycle Year: 1974
Reputation: 7889727
ParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond repute
Default

Quote:
Originally Posted by 60Gunner View Post
Probably not necessary especially if you dont disturb the cylinders. If you do it means means pulling at least 1 wrist pin clip per and the wrist pins. Leave the pistons in the cylinders or you're doing rings.
I'd try getting the broken studs out without removing the heads first.
Rather hard in my opinion to not disturb the cylinder when pulling the heads. I didn't do mine and developed a base gasket leak so I had to pull everything to simply replace the base gasket.

I never removed the wrist pins, I was able to slip a ring compressor over the piston and slide the cylinder over the piston and rings.
__________________
"I won't be wronged, I won't be insulted, and I won't be laid a hand on. I don't do these things to other people and I require the same from them."
John Wayne - "The Shootist"

[URL="https://chrisridingadventures.wordpress.com/"]Check out my Blog[/URL] for my trip reports:

[URL="https://www.buzzsprout.com/129999/841095-episode-170-interview-with-chris-comly-of-chris-riding-adventures-blog"]Click here [/URL]to listen to my interview about my Sporty and riding on the Motorcycle Men Podcast

[URL="https://www.buzzsprout.com/129999/2188085-episode-221-interview-with-iron-butt-rally-veteran-chris-comly?fbclid=IwAR2AuBjIEvI8AoLtC7ZCZ4VC5Er_Guo8WfaRjh-15tRD9a5_rLYlp_jdJBg"]Click here [/URL]to listen to my interview about the Iron Butt Rally on the Motorcycle Men Podcast
[URL="https://horizon.bmwmoa.org/episode-93-chris-comly/"]
Click here[/URL] to listen to my interview on the Chasing the Horizon Podcast


[URL="http://sportsterpedia.com/doku.php/start"]Click here for the Sportsterpedia![/URL] for technical information & advice
Reply With Quote
  #14  
Old 29th May 2019
60Gunner's Avatar
60Gunner 60Gunner is offline
Senior Custom Bike Builder
 
Join Date: Sep 2017
Location: United States
Posts: 2,940
Sportster/Buell Model: 1200/1250C
Sportster/Buell Year: 05
Reputation: 3247009
60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute
Default

Quote:
Originally Posted by ParrotHead View Post
Rather hard in my opinion to not disturb the cylinder when pulling the heads. I didn't do mine and developed a base gasket leak so I had to pull everything to simply replace the base gasket.

I never removed the wrist pins, I was able to slip a ring compressor over the piston and slide the cylinder over the piston and rings.
When I pulled my heads, my front cylinder stayed stuck down even tapping the head loose. Had to hit the cylinder several times to break it loose once I decided to pull it.
A local Indy that does machine work for the dealership too says broke loose or not, he just torques them back down and never had one leak. Mostly the old stock ones that use the oring I think.
I know Hammer has reused the mls gaskets too. Base and head. I reused them recently myself. Pulled the heads and retorqued with the same mls base gaskets.
I ended up going with a 1250 and never did bolt the old paper ones back down. Fortunately all the old gasket material came with the old cylinders. Have fun cleaning them off the cylinders to replace. The paper base gasket is a biotch to get off.

Last edited by 60Gunner; 29th May 2019 at 14:57..
Reply With Quote
  #15  
Old 29th May 2019
aswracing's Avatar
aswracing aswracing is offline
A Million Facts & Figures
 
Join Date: Jan 2005
Location: Famous Potatoes
Posts: 10,210
Sportster/Buell Model: XL883
Sportster/Buell Year: 2007
Sportster/Buell Model #2: Buell Cyclone
Sportster/Buell Year #2: 1999
Reputation: 2979240
aswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond repute
Default

Quote:
Originally Posted by herostar View Post
Hello everyone!

I had two exhaust studs break off, one in each cylinder head, so I'm going to need to remove the heads to get the broken studs extracted/replaced at a machines shop.

My question for you all: What else should I be doing while the heads are off? I'm not looking to go deep porting/polishing or anything, but am curious if there are "normal" maintenance things I should take care of while everything is off the bike.

FYI this is for a 2003 XB9R

Thanks in advance for your help!
If you get the proper tool for drilling out the studs, you don't need to pull the heads. I think you'll be surprised how easy it is. Just go through the procedure for rotating the motor down, which is described in the service manual. You'll have enough access to do the job.

My advise is don't even waste your time trying to unscrew the old studs. They're going to be stuck in there like you can't believe and the chances of unscrewing one are slim. The studs are an interference fit thread on the head side. That means they're designed to bind up in there, and they do a mighty fine job, too, especially after 16 years of being heat cycled. Not to say it's never been done, but it's just unlikely you're going to unscrew a broken off stud.

And whatever you do, don't let an easy-out get within 10 feet of your bike. I can't begin to tell you how many heads have come into the shop with a broken off easy out embedded in an exhaust stud. Now the only cure is carbide end mills, which are expensive and easily broken. An easy-out has about a .0001% chance of unscrewing that stud and a 99.9999% chance of breaking off. Don't go there.

Here's what you want:



The drill jig works slick as hell. It sits in the pocket where the exhaust gasket goes, that aligns it. You use the good stud to bolt it down. Now you just drill with a 1/4" drill bit. The jig makes it go straight through the stud. When you're done drilling, you'll have a hollowed-out shell of the stud left in the head, but it generally comes out pretty easy. Often you can do the whole job with little to no damage to the threads in the head. Just remove the hollowed out stud and screw in a new one. Maybe chase it with a tap first.

I suggest replacing it with the factory stud, because aftermarket ones don't have an interference fit thread on the head side. The interference fit thread is what keeps it from coming out of the head when you remove the exhaust. Loctite red isn't going to be effective there, it's too hot.

You may be able to find other brands of this drill fixture cheaper than the above, too, maybe someone will chime in with a link.

The reason the studs break is partly because they get fatigued over the years, but also because of exhaust mounting issues. To the extent the exhaust is allowed to move independently of the motor, it's flexing those connections to the heads. Often a poorly mounted exhaust will cause the nuts to loosen up from this flexing. I've seen guys use locking nuts to keep them on, but that's treating the symptom, and really just making it more likely to break a stud. The root cause of the issue is the exhaust mounting to the motor.

Back in the tube frame days, this was just a terrible issue on Buells. Buell finally came out with an updated mount - the one that attaches the front of the muffler to the motor - that was considerably stiffer. This about 90% fixed the issue, failures became much more rare.
__________________
Click Here to Contact Me

Reply With Quote
  #16  
Old 30th May 2019
ParrotHead's Avatar
ParrotHead ParrotHead is offline
XL FORUM TEAM MEMBER
 
Join Date: Aug 2006
Location: Near Philly
Posts: 7,965
Sportster/Buell Model: 1200R
Sportster/Buell Year: 2006
Sportster/Buell Model #2: 1200R
Sportster/Buell Year #2: 2007
Other Motorcycle Model: Suzuki GT550
Other Motorcycle Year: 1974
Reputation: 7889727
ParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond repute
Default

Quote:
Originally Posted by aswracing View Post
When you're done drilling, you'll have a hollowed-out shell of the stud left in the head, but it generally comes out pretty easy.
Ok, dumb question. Once you have the hollowed out stud how do you remove it?
Reply With Quote
  #17  
Old 30th May 2019
shanneba shanneba is online now
XL FORUM TEAM MEMBER
 
Join Date: Jul 2013
Location: Franklin, Indiana
Posts: 2,281
Sportster/Buell Model: XL1200C
Sportster/Buell Year: 2013
Reputation: 3292304
shanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond repute
Default

"Clear out remaining pieces of stud by running a 5/16 x 18 tap through hole to restore threads."

https://img.jpcycles.com/staticwebfi...df/440-266.PDF
__________________
2013 XL1200C

Find your Owner's Manual, Wiring Diagram and Parts List here :

https://serviceinfo.harley-davidson....cle/lookupForm
Enter your VIN OR
Use the search - enter year and model

If something doesn't work on your Sportster look here:
SportsterPedia.com
Reply With Quote
  #18  
Old 4th June 2019
herostar herostar is offline
XL FORUM TEAM MEMBER
 
Join Date: Aug 2018
Posts: 45
Sportster/Buell Model: xl1200r
Sportster/Buell Year: 2007
Sportster/Buell Model #2: XB9R
Sportster/Buell Year #2: 2003
Reputation: 5444
herostar is just really niceherostar is just really niceherostar is just really niceherostar is just really niceherostar is just really niceherostar is just really niceherostar is just really niceherostar is just really niceherostar is just really niceherostar is just really niceherostar is just really nice
Default

This is great info, thanks to all of you who have contributed. I'll post back once some progress is made to let you know how things work out.
__________________
2007 XL1200R - Denver, CO
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT +1. The time now is 01:26.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
XL Forum® - Linson Media LLC