The Sportster and Buell Motorcycle Forum - The XLFORUM®
 

Go Back   The Sportster and Buell Motorcycle Forum - The XLFORUM® > SPORTSTER MOTORCYCLE FORUM > Sportster Motorcycle Suspension, Frame, Forks, Handlebars, Fuel Tank, Oil Tank, Fenders
XLF Blogs XLF Arcade XLF Disclaimer/Privacy Statement/Terms Of Use

Sportster Motorcycle Suspension, Frame, Forks, Handlebars, Fuel Tank, Oil Tank, Fenders Discuss Sportster Motorcycle Suspension, Frame, Forks, Handlebars, Fuel Tank, Oil Tank, Fenders problems, advice, and/or how tos.

Active Threads
0 Gave up and made a bigger fuel tank (see pic)
Last Post: Iron Mike
Posted On: 5 Minutes Ago
Replies: 9
Views: 239
0 I guess I'm back
Last Post: gravydog
Posted On: 8 Minutes Ago
Replies: 26
Views: 591
0 Peak Prices on Our Passion ?
Last Post: rokytnji
Posted On: 10 Minutes Ago
Replies: 14
Views: 292
0 Tools to Lend Out to Forum Members
Last Post: Evil Wayz
Posted On: 20 Minutes Ago
Replies: 9
Views: 3,415
0 1991 frame/engine original ground locations
Last Post: John Harper
Posted On: 25 Minutes Ago
Replies: 11
Views: 165
0 .551 Cams in an EFI 1200
Last Post: 60Gunner
Posted On: 34 Minutes Ago
Replies: 55
Views: 1,884
0 sproket issues
Last Post: Scuba10jdl
Posted On: 49 Minutes Ago
Replies: 3
Views: 63
0 You asked for it! "The Tess' Coffee Thread"
Last Post: Flame__
Posted On: 49 Minutes Ago
Replies: 10,731
Views: 852,800
0 Official XL Forum Random Image Thread (NO NUDITY!)
Last Post: Graywolf
Posted On: 1 Hour Ago
Replies: 44,059
Views: 6,896,352
0 2019 East Coast Meet and Greet
Last Post: beeman07
Posted On: 2 Hours Ago
Replies: 321
Views: 35,382
0 ***DK Custom-Improved Front Suspension w/ Intiminator Fork Valves***
Last Post: Jollly Rogers
Posted On: 2 Hours Ago
Replies: 5
Views: 686
0 will not start
Last Post: 01rk
Posted On: 3 Hours Ago
Replies: 24
Views: 643
0 ....1
Last Post: Graywolf
Posted On: 3 Hours Ago
Replies: 4,877
Views: 282,626
0 Parrothead and the 2019 Iron Butt Rally
Last Post: shanneba
Posted On: 3 Hours Ago
Replies: 29
Views: 877
0 Jockey Shifter on a Right Side Shift Bike?
Last Post: dodgetrucken
Posted On: 3 Hours Ago
Replies: 45
Views: 15,180
0 Hottie of the day, no nudity.
Last Post: Stairman
Posted On: 3 Hours Ago
Replies: 11,710
Views: 1,052,196
0 This is gonna hurt.
Last Post: Stairman
Posted On: 3 Hours Ago
Replies: 7,673
Views: 1,502,541
0 Roads I'd like to ride.
Last Post: Stairman
Posted On: 3 Hours Ago
Replies: 1,865
Views: 156,916
0 Stator wire hot!
Last Post: IXL2Relax
Posted On: 4 Hours Ago
Replies: 25
Views: 542
0 PLEASE READ THIS Before You Post In 'The BUY - SELL - TRADE Zone'!
Last Post: Folkie
Posted On: 4 Hours Ago
Replies: 1
Views: 507
0 Stock air cleaner box modifications
Last Post: harley506d
Posted On: 6 Hours Ago
Replies: 293
Views: 182,677
0 Wet sumping?
Last Post: Hippysmack
Posted On: 8 Hours Ago
Replies: 88
Views: 3,114
6 Blast Project (and will be needing help most likely)
Last Post: Hornsmith
Posted On: 8 Hours Ago
Replies: 24
Views: 522
10 New to the HD world, Ironhrad vs Shovel, whats the diff
Last Post: A Seabee
Posted On: 8 Hours Ago
Replies: 29
Views: 631
0 72 XLH1000 Wiring Kit
Last Post: brianbbs67
Posted On: 10 Hours Ago
Replies: 9
Views: 188
0 This week on Craig's list
Last Post: A Seabee
Posted On: 10 Hours Ago
Replies: 4,113
Views: 471,664
0 Some oil issues!
Last Post: Hippysmack
Posted On: 11 Hours Ago
Replies: 16
Views: 467
5 How do you Wash your Bike?
Last Post: xElvis
Posted On: 11 Hours Ago
Replies: 19
Views: 424
0 Mystery drip off rear brake cylinder
Last Post: rocketmangb
Posted On: 11 Hours Ago
Replies: 5
Views: 97
0 Calling all "Long Frame" riders...
Last Post: Whitewalls
Posted On: 12 Hours Ago
Replies: 4
Views: 322
More...
Members Birthdays
NedNimrod, jduffy01, AlanT (71), jzink0883 (70), LVBOATDOC (67), glef (62), Dogsbd (57), wmbettsjr (43), darkcustom (42), jon8641 (35)
Sponsored Links
Reply
 
Share Thread Tools Display Modes
  #31  
Old 2 Weeks Ago
ChrisOfTheOT ChrisOfTheOT is offline
Biker
 
Join Date: May 2019
Posts: 14
Sportster/Buell Model: XL1200CA
Sportster/Buell Year: 2016
Reputation: 10
ChrisOfTheOT is an unknown quantity at this point
Default

Quote:
Originally Posted by Four Speed View Post
Don't do yourself down. Just explain what you need to Dave and I am sure he could tune your shocks so that you are happy.
Probably save yourself a load of cash into the bargain. Hope it goes well.
Thanks Four Speed. I have spoken to the legend that is 'Dave-at-Hagon'. He suggested increasing the pre-load to mid-position, which I've done and will test tomorrow. (Damping is also mid-position, 5 of 10, but I'll fiddle with that too.)

He also took some time to offer this in an email:
On [injected] Sportsters there are two issues which are the Achilles' heel…:

1. If you were to remove the rear shocks and lift the rear wheel and swing arm upwards, there is contact when the shock eye's get to 244mm apart… and if you take the belt guard off the tyre hits the rear fender [he means 'mudguard'...] just slightly after.

Consequently the standard shock bottoms out at 250mm to avoid this issue, therefore a model with shocks 300mm long will only have 50mm of travel, of which 10-12mm... is bump stop rubber.

A typical twin shock would have 80mm of stroke or travel, so if you take that 250mm compressed length and add the typical 80mm travel you have an overall length of 330mm or 13". And more importantly another 30mm of travel!

If 330mm is too much for you to be happy with the bike cosmetically, every additional 10mm step in length increased from the original 300mm shock will be an additional 10mm of travel which is of course ride quality.

2. Harley tend to use quite a soft spring with a large amount of preload. This normally makes a harsher ride for very light riders and a shock which will easily bottom out for anyone 12st plus and, of course, any one riding two up is riding on the bump stop.

Also, since Shanneba's thread is about the SE fork upgrage(!), I have long wanted to get better fork springs. Dave has written elsewhere that Harely forks are 'under sprung and over dampened'. This, coupled with the low ride height, means the SE fork spring kit is a fab option... when I can pay for it. I always balked 'cos I've never read a real review from a real rider. Now, Shanneba has convinced me. (Thanks again mate!)

Cheers,

Chris

Last edited by ChrisOfTheOT; 2 Weeks Ago at 17:50.. Reason: Grammar, innit...
Reply With Quote
  #32  
Old 2 Weeks Ago
Four Speed Four Speed is offline
Senior Chief Master Mechanic 2nd Class
 
Join Date: Dec 2015
Posts: 1,520
Sportster/Buell Model: Sportster 883 Hugger
Sportster/Buell Year: 1988
Reputation: 543828
Four Speed has a reputation beyond reputeFour Speed has a reputation beyond reputeFour Speed has a reputation beyond reputeFour Speed has a reputation beyond reputeFour Speed has a reputation beyond reputeFour Speed has a reputation beyond reputeFour Speed has a reputation beyond reputeFour Speed has a reputation beyond reputeFour Speed has a reputation beyond reputeFour Speed has a reputation beyond reputeFour Speed has a reputation beyond repute
Default

ChrisOfTheOT, you normally set up suspension so that it cycles somewhere mid-stroke and uses the full travel occasionally on hard bumps.
That is normal. You just don't want the shocks bottoming out routinely with little progression so they jolt your spine. Here, shanneba
is setting up his shocks to sag a bit more by reducing the preload, while increasing the compression damping slightly. That should give slightly
more movement per bump with a bit more progressive damping on compression. Sag affects and rebound damping will affect how
fast the shocks return which affects compliance and comfort.

I am glad Dave offered that useful advice. Dave is right about the spring HD rates and adjusting the damping. Preload and damping
could make a lot of difference. So in your case you are blowing through the travel so you need more preload and compression damping.
When you are happy that is better, then play with the rebound damping until you get a smooth rebound without bucking.

We didn't really discuss the effects that balancing the font suspension has on the rear. In general you want the fork responding in a
similar way to the rear shocks, albeit with more movement. A real limitation with HD forks is the damper rod which is a very basic damper.
It does not respond well to square edged bumps or hard braking. A modern shim stack damping system is a better way to go. You get better
mid-stroke compliance as well as better drive control even with a standard spring. You can simply add damper inserts like Gold valves or Ricor
Intimidators that offer remarkable improvements in ride quality for about a quarter/third of the cost of shannebas SE conversion. I hate to think
what the SE kit would cost in Europe! But shanneba allows us to enjoy them vicariously.
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Sponsored Links
All times are GMT +1. The time now is 15:01.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
XL Forum® - Linson Media LLC