The Sportster and Buell Motorcycle Forum - The XLFORUM®
 

Go Back   The Sportster and Buell Motorcycle Forum - The XLFORUM® > BUELL MOTORCYCLE ZONE > Buell Motorcycle Accessories
XLF Blogs XLF Arcade XLF Disclaimer/Privacy Statement/Terms Of Use

Notices

Active Threads
0 Was your 1st bike a Sportster?
Last Post: lmarshall73
Posted On: 1 Minute Ago
Replies: 971
Views: 210,384
0 Oil Pump upgrade
Last Post: hotrodbiker
Posted On: 1 Minute Ago
Replies: 10
Views: 244
0 one sporty and $5000... What would you do?
Last Post: jordan1200
Posted On: 2 Minutes Ago
Replies: 274
Views: 126,730
0 What did you do for your sporty Today?
Last Post: Crusty
Posted On: 11 Minutes Ago
Replies: 5,213
Views: 566,364
0 check my chain?
Last Post: Four Speed
Posted On: 14 Minutes Ago
Replies: 5
Views: 203
0 1990 Sportster. Something is pulling voltage from battery??
Last Post: Four Speed
Posted On: 20 Minutes Ago
Replies: 1
Views: 17
0 My take on the world ~ Photo by Trace
Last Post: Nibelungen
Posted On: 23 Minutes Ago
Replies: 764
Views: 80,784
0 Bob from Appleton WI
Last Post: Stairman
Posted On: 24 Minutes Ago
Replies: 4
Views: 41
0 How many Sporty seats ya got for one ass?
Last Post: VaFish
Posted On: 28 Minutes Ago
Replies: 258
Views: 50,739
0 Screw Loose's Repairs
Last Post: ParrotHead
Posted On: 54 Minutes Ago
Replies: 305
Views: 44,350
0 New Hammer Impact Air Intake Powder Coated
Last Post: Outtakes
Posted On: 57 Minutes Ago
Replies: 4
Views: 153
0 first change, very little oil
Last Post: rocketmangb
Posted On: 57 Minutes Ago
Replies: 2
Views: 41
0 As far as maintenance goes...Cycle Electric or Alternator?
Last Post: Silky Johnson
Posted On: 1 Hour Ago
Replies: 2
Views: 72
0 Who Runs Turn Signals?
Last Post: vagrant318
Posted On: 1 Hour Ago
Replies: 341
Views: 66,983
0 Free to a Good Home (pay $8 shipping only):2014 FSM, used
Last Post: rocketmangb
Posted On: 1 Hour Ago
Replies: 6
Views: 337
0 Removing powder coat?
Last Post: Oli1200
Posted On: 1 Hour Ago
Replies: 10
Views: 359
0 883 Sportster in Baja
Last Post: VaFish
Posted On: 1 Hour Ago
Replies: 0
Views: 28
0 Official XL Forum Random Image Thread (NO NUDITY!)
Last Post: Graywolf
Posted On: 1 Hour Ago
Replies: 40,917
Views: 6,274,565
0 Shotgun Porn
Last Post: Stairman
Posted On: 1 Hour Ago
Replies: 767
Views: 97,616
0 What oil temp do you run
Last Post: sportysrock
Posted On: 1 Hour Ago
Replies: 89
Views: 16,643
0 Passenger floorboards and sissy bar questions
Last Post: chris16371
Posted On: 1 Hour Ago
Replies: 27
Views: 614
0 THE Trainspotting Thread
Last Post: Stairman
Posted On: 1 Hour Ago
Replies: 1,982
Views: 201,906
0 1962 XLCH Front Wheel WTB
Last Post: Jaykel
Posted On: 2 Hours Ago
Replies: 2
Views: 69
0 Stuck in fist after a spill
Last Post: amfxlh
Posted On: 2 Hours Ago
Replies: 2
Views: 82
0 Crusty's Travels
Last Post: SonWon
Posted On: 2 Hours Ago
Replies: 1,471
Views: 145,403
0 Fact or Fiction - HP Claims
Last Post: jcro61
Posted On: 2 Hours Ago
Replies: 741
Views: 85,482
0 Primary/transmission synthetic oil
Last Post: 60Gunner
Posted On: 2 Hours Ago
Replies: 25
Views: 660
3 Wtb, Wts, Wtt, Wtg (Rubber Mounts)
Last Post: wongjohnson
Posted On: 3 Hours Ago
Replies: 24
Views: 34,732
4 Cross Country Prep
Last Post: doodah man
Posted On: 3 Hours Ago
Replies: 12
Views: 485
0 :( New deep rebuild on my 90 inch
Last Post: jkinkade
Posted On: 4 Hours Ago
Replies: 80
Views: 6,820
More...
Members Birthdays
stevervp, philvet (75), outlawreb (63), rabes56 (62), Bigmatt (60), Beaker666 (54), hippiemwc (54), wumm883c (52), 2wheeltodd (51), israel (46), XRWeasel (44), Stitch (41), Dekooy (35), Titaniumrust (35), Ameri-Deutsch (34)
Sponsored Links
Reply
 
Share Thread Tools Display Modes
  #1  
Old 2nd December 2008
josephthreedogs's Avatar
josephthreedogs josephthreedogs is offline
Greasemonkey
 
Join Date: Jun 2008
Location: Las Vegas, Nevada
Posts: 124
Sportster/Buell Model: Hugger
Sportster/Buell Year: 02
Sportster/Buell Model #2: S3T
Sportster/Buell Year #2: '02
Other Motorcycle Model: many, over 14 other bikes
Other Motorcycle Year: asso
Reputation: 58
josephthreedogs is an unknown quantity at this point
Default XB9 heated grips

Is the XB9 prewired for factory heated grips, or will I have to tap into the stock wiring harness?
Reply With Quote
  #2  
Old 2nd December 2008
Bob F's Avatar
Bob F Bob F is offline
XLF LIFEMEMBER Im retired
 
Join Date: Feb 2007
Location: Pittsburgh, PA
Posts: 14,306
Sportster/Buell Model: XL50 0596 Black
Sportster/Buell Year: 2007
Other Motorcycle Model: E-Glide
Other Motorcycle Year: 2003
Reputation: 465884
Bob F has a reputation beyond reputeBob F has a reputation beyond reputeBob F has a reputation beyond reputeBob F has a reputation beyond reputeBob F has a reputation beyond reputeBob F has a reputation beyond reputeBob F has a reputation beyond reputeBob F has a reputation beyond reputeBob F has a reputation beyond reputeBob F has a reputation beyond reputeBob F has a reputation beyond repute
Default

FWIW They lasted 40,000 on my old E-Glide and I did replace them. They were nice on mild days but didn't do much when it was cold. My 2¢.
__________________
Bob, a glutton and a winebibber, a friend of bartenders and sinners!
Reply With Quote
  #3  
Old 7th December 2008
firebrick43's Avatar
firebrick43 firebrick43 is offline
Greasemonkey
 
Join Date: Aug 2006
Posts: 106
Sportster/Buell Model: XL883
Sportster/Buell Year: 2007
firebrick43 has disabled reputation
Default

While not positive, I pretty sure an xb9 is not prewired for heated grips. Please forgive me if I am incorrect about this but my experience is more towards sporsters. The best way to wire grips takes some work but will pay divideds down the way in less maintenence. There should be an unused fuse space on the fuse block. Some will have the hot side installed while others will not have any thing installed. Go to the buell dealer and ask for the fuse block terminals, they should be under 5 bucks for a couple of them. Unmounted the fuse block so you can reach the back side. Take a 14 gauge wire of decent quality and crimp/solder the terminal to the wire and insert it into the fuse across from one that has the hot side. If no live terminals are in the spare slots you might have to run a wire to the battery. If your back there its better to wire up all the spare terminals to just in case you want to add more farkles later.

Now run the wire up to the a small on/off/on micro switch somewhere in the inside fairing or mounted in an accessory switch housing if buell offers such a beast.

You have 3 options from here. You can buy the factory grips for big bucks and the performance is not that great. You can buy dual star grips heaters http://www.dual-star.com/index2/Ride...d_grip_kit.htm , performance is better and you can use any grip you want but eventually, like the factory heated grips, the wire that feed the throttle grip will fail. These first two are the best options however if you are running aluminum handle bars as aluminum is such a good conductor of heat. The third option is what I have, and that is polly heaters. They work wonderful in steel bars, much better than the first two options, and they are installed inside the bars so they wont have wiring problems later on down the road from wire movement. It takes more time to install but they are inexpensive. I have the snowmobile model which is very effective down to 20 degrees with out any hand wind protection and decent gloves. Below that you palms stay warm(hot, hot, hot on high) but even with really good gloves the back of my hand gets cold.

The wires on these heaters is the best quality I have seen, as good as milspec aircraft wiring. The switch however is horrible, get their upgraded switch or one from radio shack. Its a family business and are wonderful to work with. A couple of years ago when I purchased mine, they didn't take credit cards, but sent me the heaters with an invoice, letting me send a check after receipt of the goods, a throw back to the old days.
Reply With Quote
  #4  
Old 12th December 2008
josephthreedogs's Avatar
josephthreedogs josephthreedogs is offline
Greasemonkey
 
Join Date: Jun 2008
Location: Las Vegas, Nevada
Posts: 124
Sportster/Buell Model: Hugger
Sportster/Buell Year: 02
Sportster/Buell Model #2: S3T
Sportster/Buell Year #2: '02
Other Motorcycle Model: many, over 14 other bikes
Other Motorcycle Year: asso
Reputation: 58
josephthreedogs is an unknown quantity at this point
Default

Thanks for the info, my Buell mechanic at the local dealer didn't know if the bike was pre-wired or not. I'll just do it myself now.
Reply With Quote
  #5  
Old 17th December 2008
xl1200r's Avatar
xl1200r xl1200r is offline
Senior Custom Bike Builder
 
Join Date: Nov 2004
Location: North Greenbush, NY
Posts: 2,955
Sportster/Buell Model: Buell 1125CR
Sportster/Buell Year: 2009
Sportster/Buell Model #2: XLCH
Sportster/Buell Year #2: 1964
Other Motorcycle Model: Kawasaki Ninja 250
Other Motorcycle Year: 2006
Reputation: 1866
xl1200r has a spectacular aura aboutxl1200r has a spectacular aura aboutxl1200r has a spectacular aura aboutxl1200r has a spectacular aura aboutxl1200r has a spectacular aura aboutxl1200r has a spectacular aura aboutxl1200r has a spectacular aura aboutxl1200r has a spectacular aura aboutxl1200r has a spectacular aura aboutxl1200r has a spectacular aura aboutxl1200r has a spectacular aura about
Default

It depends on what year the Buell is. All Buells, 2008 and newer, are prewired from the factory for heated grips. There is an accesory plug that you use (you can also build your own plugs to plug in a GPS or some other accessory).

If you are 2007 or older, you'll need to tap in.
Reply With Quote
  #6  
Old 17th December 2008
chopperdave's Avatar
chopperdave chopperdave is offline
11sec CLUB, MEMBER
 
Join Date: Jan 2005
Posts: 106
Sportster/Buell Model: 1474 (diguised as 883)
Sportster/Buell Year: 94
Sportster/Buell Model #2: 2004 buell xb12ssnc
chopperdave has disabled reputation
Thumbs up grips

Quote:
Originally Posted by firebrick43 View Post
While not positive, I pretty sure an xb9 is not prewired for heated grips. Please forgive me if I am incorrect about this but my experience is more towards sporsters. The best way to wire grips takes some work but will pay divideds down the way in less maintenence. There should be an unused fuse space on the fuse block. Some will have the hot side installed while others will not have any thing installed. Go to the buell dealer and ask for the fuse block terminals, they should be under 5 bucks for a couple of them. Unmounted the fuse block so you can reach the back side. Take a 14 gauge wire of decent quality and crimp/solder the terminal to the wire and insert it into the fuse across from one that has the hot side. If no live terminals are in the spare slots you might have to run a wire to the battery. If your back there its better to wire up all the spare terminals to just in case you want to add more farkles later.

Now run the wire up to the a small on/off/on micro switch somewhere in the inside fairing or mounted in an accessory switch housing if buell offers such a beast.

You have 3 options from here. You can buy the factory grips for big bucks and the performance is not that great. You can buy dual star grips heaters http://www.dual-star.com/index2/Ride...d_grip_kit.htm , performance is better and you can use any grip you want but eventually, like the factory heated grips, the wire that feed the throttle grip will fail. These first two are the best options however if you are running aluminum handle bars as aluminum is such a good conductor of heat. The third option is what I have, and that is polly heaters. They work wonderful in steel bars, much better than the first two options, and they are installed inside the bars so they wont have wiring problems later on down the road from wire movement. It takes more time to install but they are inexpensive. I have the snowmobile model which is very effective down to 20 degrees with out any hand wind protection and decent gloves. Below that you palms stay warm(hot, hot, hot on high) but even with really good gloves the back of my hand gets cold.

The wires on these heaters is the best quality I have seen, as good as milspec aircraft wiring. The switch however is horrible, get their upgraded switch or one from radio shack. Its a family business and are wonderful to work with. A couple of years ago when I purchased mine, they didn't take credit cards, but sent me the heaters with an invoice, letting me send a check after receipt of the goods, a throw back to the old days.
hi,the 3rd,( polly heaters)do they have a web,or e-mail, or snail mail?

thanks
Chopp
Reply With Quote
  #7  
Old 14th December 2010
LifesHarlequin's Avatar
LifesHarlequin LifesHarlequin is offline
Master Mechanic
 
Join Date: Aug 2008
Location: NAF Atsugi, Japan
Posts: 299
Sportster/Buell Model: XB9SX
Sportster/Buell Year: 2007
Other Motorcycle Model: Bicycles (Daily Rider)
Other Motorcycle Year: 2009
Reputation: 2327
LifesHarlequin is a jewel in the roughLifesHarlequin is a jewel in the roughLifesHarlequin is a jewel in the roughLifesHarlequin is a jewel in the roughLifesHarlequin is a jewel in the roughLifesHarlequin is a jewel in the roughLifesHarlequin is a jewel in the roughLifesHarlequin is a jewel in the roughLifesHarlequin is a jewel in the roughLifesHarlequin is a jewel in the roughLifesHarlequin is a jewel in the rough
Default

Has anyone actually had their 07 or older Buell tapped for the stock heated grips? Its getting down to 10deg at night here, and despite needing better gloves, I'm tempted to get the oft reviewed "hot/too hot" stock grips put on. Plus I wanna keep the stock look. I'd prefer to just do it myself, and can't anyone on the net that's posted an install of a 07 or older lightning.
__________________
2007 XB9SX Hero Blue (Bone Stock)
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Sponsored Links
All times are GMT +1. The time now is 16:02.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
XL Forum® - Linson Media LLC