The Sportster and Buell Motorcycle Forum - The XLFORUM®
 

Go Back   The Sportster and Buell Motorcycle Forum - The XLFORUM® > BUELL MOTORCYCLE FORUM > Buell Motorcycle Top End
XLF Blogs XLF Arcade XLF Disclaimer/Privacy Statement/Terms Of Use

Active Threads
0 Wire question, 30A breaker to starter...
Last Post: LenC
Posted On: 3 Minutes Ago
Replies: 0
Views: 1
0 Roadside Manners
Last Post: owlsplace
Posted On: 8 Minutes Ago
Replies: 0
Views: 3
0 My wife wanted a Swimming Pool
Last Post: Toejam503
Posted On: 10 Minutes Ago
Replies: 14
Views: 728
0 Patriot Defender whats the next best exhaust?
Last Post: madnss
Posted On: 12 Minutes Ago
Replies: 167
Views: 32,381
0 Ride Report 2019 Black Hills, Grand Teton Mtns., Rocky Mountain Ntl. Park
Last Post: DK Custom
Posted On: 15 Minutes Ago
Replies: 58
Views: 2,382
0 Cold Start. Then stall
Last Post: Lukidj
Posted On: 30 Minutes Ago
Replies: 12
Views: 331
0 Triumph or Harley!
Last Post: heyshott 81
Posted On: 30 Minutes Ago
Replies: 12
Views: 525
8 Rear Brake Light Switch Bad
Last Post: THEWILDONE
Posted On: 41 Minutes Ago
Replies: 12
Views: 5,416
0 What song do you have stuck in your head?
Last Post: heyshott 81
Posted On: 45 Minutes Ago
Replies: 2,219
Views: 199,107
0 28 years later..
Last Post: Highly-Dangerous
Posted On: 56 Minutes Ago
Replies: 31
Views: 1,120
0 In tank pump and filter work
Last Post: smm1200
Posted On: 1 Hour Ago
Replies: 2
Views: 145
0 Hardtail frame conversion with 3" stretch and avoiding a chain conversion kit
Last Post: jharback
Posted On: 1 Hour Ago
Replies: 7
Views: 205
0 Pushrod cover seals
Last Post: mfc
Posted On: 2 Hours Ago
Replies: 5
Views: 112
0 Alternator/generator Conversion
Last Post: wymanv
Posted On: 2 Hours Ago
Replies: 139
Views: 68,900
12 POLL: How many times have you dropped a motorcycle?
Last Post: Graywolf
Posted On: 2 Hours Ago
Replies: 638
Views: 113,039
2 Memory Highway
Last Post: Highly-Dangerous
Posted On: 2 Hours Ago
Replies: 1
Views: 59
0 Official XL Forum Random Image Thread (NO NUDITY!)
Last Post: Graywolf
Posted On: 3 Hours Ago
Replies: 44,377
Views: 6,969,065
0 Hot Rods, Rat Rods, and Customs.
Last Post: Stairman
Posted On: 3 Hours Ago
Replies: 3,524
Views: 416,849
0 Hottie of the day, no nudity.
Last Post: Stairman
Posted On: 3 Hours Ago
Replies: 12,293
Views: 1,120,902
0 2010 xl 1200 low solo seat fit
Last Post: Folkie
Posted On: 3 Hours Ago
Replies: 6
Views: 149
0 Hi From NJ
Last Post: Calcustom
Posted On: 4 Hours Ago
Replies: 15
Views: 253
0 Cost of ejikation
Last Post: owlsplace
Posted On: 4 Hours Ago
Replies: 1
Views: 157
0 What did you do for your sporty Today?
Last Post: Skuzeee
Posted On: 4 Hours Ago
Replies: 6,140
Views: 780,462
0 Best way to 883->1200cc ?
Last Post: aswracing
Posted On: 4 Hours Ago
Replies: 13
Views: 435
0 Clutch issues
Last Post: rocketmangb
Posted On: 4 Hours Ago
Replies: 10
Views: 280
0 Primary will not seal
Last Post: Toejam503
Posted On: 5 Hours Ago
Replies: 2
Views: 72
0 Tillotson Welch Plugs
Last Post: Coz
Posted On: 5 Hours Ago
Replies: 0
Views: 61
14 HD ad for Dirt?
Last Post: gusm2
Posted On: 7 Hours Ago
Replies: 2
Views: 165
0 Bearing questions
Last Post: bustert
Posted On: 7 Hours Ago
Replies: 12
Views: 462
0 Turn signals and switch required 1972 xlch
Last Post: bustert
Posted On: 7 Hours Ago
Replies: 4
Views: 181
More...
Members Birthdays
oakies, Gunhappy2 (61), SamIam (55), biggdann (49), boyer911 (49), danii (42), PVD24 (40)
Sponsored Links
Reply
 
Share Thread Tools Display Modes
  #11  
Old 28th May 2019
60Gunner's Avatar
60Gunner 60Gunner is offline
Chief of Security
 
Join Date: Sep 2017
Location: United States
Posts: 1,383
Sportster/Buell Model: 1200/1250C
Sportster/Buell Year: 05
Reputation: 1626312
60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute
Default

Quote:
Originally Posted by Sprtstr1200s View Post
I don't know what shape my springs are in. Haven't opened the motor yet.
Your stock ones were just weaker to begin with. Fine til you start putting cams in.
__________________
05 1200/1250C/Hammer 570 Cams/E1 clutch kit
TC88A Gunner's V00D00 map/DCPR7E/Taylor Pro 8mm
S&S Premium Lifters/KhromeWerks HP Plus 3" slip ons
HSR42 25 pilot 1 1/2 turns 97 needle 2nd groove 170 main
Dragtron II AC K&N filter/VR1 20W50/Spectro 85wt Primary Oil

Reply With Quote
  #12  
Old 28th May 2019
Sprtstr1200s's Avatar
Sprtstr1200s Sprtstr1200s is offline
XL FORUM TEAM MEMBER
 
Join Date: Aug 2016
Location: Space Coast
Posts: 783
Sportster/Buell Model: Sportster XL1200s
Sportster/Buell Year: 1999
Reputation: 369853
Sprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond reputeSprtstr1200s has a reputation beyond repute
Default

Spent an weekend screwing around testing springs, new, old. Amazed at the variations. https://www.bing.com/images/search?q...ster&FORM=IGRE
Reply With Quote
  #13  
Old 29th May 2019
ParrotHead's Avatar
ParrotHead ParrotHead is offline
I am the great Cornholio!
 
Join Date: Aug 2006
Location: Near Philly
Posts: 7,753
Sportster/Buell Model: 1200R
Sportster/Buell Year: 2006
Sportster/Buell Model #2: 1200R
Sportster/Buell Year #2: 2007
Other Motorcycle Model: Suzuki GT550
Other Motorcycle Year: 1974
Reputation: 6805827
ParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond repute
Default

Quote:
Originally Posted by 60Gunner View Post
Probably not necessary especially if you dont disturb the cylinders. If you do it means means pulling at least 1 wrist pin clip per and the wrist pins. Leave the pistons in the cylinders or you're doing rings.
I'd try getting the broken studs out without removing the heads first.
Rather hard in my opinion to not disturb the cylinder when pulling the heads. I didn't do mine and developed a base gasket leak so I had to pull everything to simply replace the base gasket.

I never removed the wrist pins, I was able to slip a ring compressor over the piston and slide the cylinder over the piston and rings.
__________________
"I won't be wronged, I won't be insulted, and I won't be laid a hand on. I don't do these things to other people and I require the same from them."
John Wayne - "The Shootist"

Check out my Blog for my trip reports:

Click here to listen to my interview on the Motorcycle Men Podcast

Click here for the Sportsterpedia! for technical information & advice
Reply With Quote
  #14  
Old 29th May 2019
60Gunner's Avatar
60Gunner 60Gunner is offline
Chief of Security
 
Join Date: Sep 2017
Location: United States
Posts: 1,383
Sportster/Buell Model: 1200/1250C
Sportster/Buell Year: 05
Reputation: 1626312
60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute60Gunner has a reputation beyond repute
Default

Quote:
Originally Posted by ParrotHead View Post
Rather hard in my opinion to not disturb the cylinder when pulling the heads. I didn't do mine and developed a base gasket leak so I had to pull everything to simply replace the base gasket.

I never removed the wrist pins, I was able to slip a ring compressor over the piston and slide the cylinder over the piston and rings.
When I pulled my heads, my front cylinder stayed stuck down even tapping the head loose. Had to hit the cylinder several times to break it loose once I decided to pull it.
A local Indy that does machine work for the dealership too says broke loose or not, he just torques them back down and never had one leak. Mostly the old stock ones that use the oring I think.
I know Hammer has reused the mls gaskets too. Base and head. I reused them recently myself. Pulled the heads and retorqued with the same mls base gaskets.
I ended up going with a 1250 and never did bolt the old paper ones back down. Fortunately all the old gasket material came with the old cylinders. Have fun cleaning them off the cylinders to replace. The paper base gasket is a biotch to get off.

Last edited by 60Gunner; 29th May 2019 at 14:57..
Reply With Quote
  #15  
Old 29th May 2019
aswracing's Avatar
aswracing aswracing is offline
A Million Facts & Figures
 
Join Date: Jan 2005
Location: Famous Potatoes
Posts: 10,017
Sportster/Buell Model: XL883
Sportster/Buell Year: 2007
Sportster/Buell Model #2: Buell Cyclone
Sportster/Buell Year #2: 1999
Reputation: 2589529
aswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond repute
Default

Quote:
Originally Posted by herostar View Post
Hello everyone!

I had two exhaust studs break off, one in each cylinder head, so I'm going to need to remove the heads to get the broken studs extracted/replaced at a machines shop.

My question for you all: What else should I be doing while the heads are off? I'm not looking to go deep porting/polishing or anything, but am curious if there are "normal" maintenance things I should take care of while everything is off the bike.

FYI this is for a 2003 XB9R

Thanks in advance for your help!
If you get the proper tool for drilling out the studs, you don't need to pull the heads. I think you'll be surprised how easy it is. Just go through the procedure for rotating the motor down, which is described in the service manual. You'll have enough access to do the job.

My advise is don't even waste your time trying to unscrew the old studs. They're going to be stuck in there like you can't believe and the chances of unscrewing one are slim. The studs are an interference fit thread on the head side. That means they're designed to bind up in there, and they do a mighty fine job, too, especially after 16 years of being heat cycled. Not to say it's never been done, but it's just unlikely you're going to unscrew a broken off stud.

And whatever you do, don't let an easy-out get within 10 feet of your bike. I can't begin to tell you how many heads have come into the shop with a broken off easy out embedded in an exhaust stud. Now the only cure is carbide end mills, which are expensive and easily broken. An easy-out has about a .0001% chance of unscrewing that stud and a 99.9999% chance of breaking off. Don't go there.

Here's what you want:



The drill jig works slick as hell. It sits in the pocket where the exhaust gasket goes, that aligns it. You use the good stud to bolt it down. Now you just drill with a 1/4" drill bit. The jig makes it go straight through the stud. When you're done drilling, you'll have a hollowed-out shell of the stud left in the head, but it generally comes out pretty easy. Often you can do the whole job with little to no damage to the threads in the head. Just remove the hollowed out stud and screw in a new one. Maybe chase it with a tap first.

I suggest replacing it with the factory stud, because aftermarket ones don't have an interference fit thread on the head side. The interference fit thread is what keeps it from coming out of the head when you remove the exhaust. Loctite red isn't going to be effective there, it's too hot.

You may be able to find other brands of this drill fixture cheaper than the above, too, maybe someone will chime in with a link.

The reason the studs break is partly because they get fatigued over the years, but also because of exhaust mounting issues. To the extent the exhaust is allowed to move independently of the motor, it's flexing those connections to the heads. Often a poorly mounted exhaust will cause the nuts to loosen up from this flexing. I've seen guys use locking nuts to keep them on, but that's treating the symptom, and really just making it more likely to break a stud. The root cause of the issue is the exhaust mounting to the motor.

Back in the tube frame days, this was just a terrible issue on Buells. Buell finally came out with an updated mount - the one that attaches the front of the muffler to the motor - that was considerably stiffer. This about 90% fixed the issue, failures became much more rare.
__________________
Click Here to Contact Me

Reply With Quote
  #16  
Old 30th May 2019
ParrotHead's Avatar
ParrotHead ParrotHead is offline
I am the great Cornholio!
 
Join Date: Aug 2006
Location: Near Philly
Posts: 7,753
Sportster/Buell Model: 1200R
Sportster/Buell Year: 2006
Sportster/Buell Model #2: 1200R
Sportster/Buell Year #2: 2007
Other Motorcycle Model: Suzuki GT550
Other Motorcycle Year: 1974
Reputation: 6805827
ParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond reputeParrotHead has a reputation beyond repute
Default

Quote:
Originally Posted by aswracing View Post
When you're done drilling, you'll have a hollowed-out shell of the stud left in the head, but it generally comes out pretty easy.
Ok, dumb question. Once you have the hollowed out stud how do you remove it?
Reply With Quote
  #17  
Old 30th May 2019
shanneba shanneba is offline
XL FORUM TEAM MEMBER
 
Join Date: Jul 2013
Location: Franklin, Indiana
Posts: 1,788
Sportster/Buell Model: XL1200C
Sportster/Buell Year: 2013
Reputation: 2354006
shanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond reputeshanneba has a reputation beyond repute
Default

"Clear out remaining pieces of stud by running a 5/16 x 18 tap through hole to restore threads."

https://img.jpcycles.com/staticwebfi...df/440-266.PDF
__________________
2013 XL1200C

Find your Owner's Manual, Wiring Diagram and Parts List here :

https://serviceinfo.harley-davidson....cle/lookupForm
Enter your VIN OR
Use the search - enter year and model

If something doesn't work on your Sportster look here:
SportsterPedia.com
Reply With Quote
  #18  
Old 4th June 2019
herostar herostar is offline
Biker
 
Join Date: Aug 2018
Posts: 23
Sportster/Buell Model: xl1200r
Sportster/Buell Year: 2007
Sportster/Buell Model #2: XB9R
Sportster/Buell Year #2: 2003
Reputation: 10
herostar is an unknown quantity at this point
Default

This is great info, thanks to all of you who have contributed. I'll post back once some progress is made to let you know how things work out.
__________________
2007 XL1200R - Denver, CO
Reply With Quote
Sponsored Links
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Sponsored Links
All times are GMT +1. The time now is 21:59.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
XL Forum® - Linson Media LLC