The Sportster and Buell Motorcycle Forum - The XLFORUM®
 

Go Back   The Sportster and Buell Motorcycle Forum - The XLFORUM® > SPORTSTER MOTORCYCLE FORUM > Sportster Motorcycle Suspension, Frame, Forks, Handlebars, Fuel Tank, Oil Tank, Fenders
XLF Blogs XLF Arcade XLF Disclaimer/Privacy Statement/Terms Of Use

Notices

Sportster Motorcycle Suspension, Frame, Forks, Handlebars, Fuel Tank, Oil Tank, Fenders Discuss Sportster Motorcycle Suspension, Frame, Forks, Handlebars, Fuel Tank, Oil Tank, Fenders problems, advice, and/or how tos.

Active Threads
0 NOS cases
Last Post: Ferrous Head
Posted On: 18 Minutes Ago
Replies: 28
Views: 965
0 Keep & Kill
Last Post: Crusty
Posted On: 28 Minutes Ago
Replies: 25,570
Views: 1,494,954
0 Official XL Forum Random Image Thread (NO NUDITY!)
Last Post: sportsterpaul
Posted On: 29 Minutes Ago
Replies: 52,517
Views: 8,864,408
0 Allegheny National Park III
Last Post: sportsterpaul
Posted On: 31 Minutes Ago
Replies: 27
Views: 594
0 Iree's late night cafe
Last Post: Graywolf
Posted On: 54 Minutes Ago
Replies: 2,175
Views: 376,053
0 71 XLH Value?
Last Post: flthd31
Posted On: 1 Hour Ago
Replies: 10
Views: 151
0 04 Sportster refurb and build.
Last Post: BillPlayfoot
Posted On: 1 Hour Ago
Replies: 35
Views: 2,470
0 Facebook sales listing
Last Post: rokytnji
Posted On: 1 Hour Ago
Replies: 0
Views: 18
0 Hello from CT
Last Post: Folkie
Posted On: 1 Hour Ago
Replies: 5
Views: 48
0 72 ih stroker advise needed
Last Post: DR DICK
Posted On: 1 Hour Ago
Replies: 16
Views: 872
0 a definitive sportster chain conversion pros and cons list
Last Post: rokytnji
Posted On: 1 Hour Ago
Replies: 27
Views: 948
0 Aftermarket nose cone module vs aftermarket under seat module
Last Post: mick42
Posted On: 2 Hours Ago
Replies: 8
Views: 193
0 1960 XLH Stroker – a 13 year journey
Last Post: brucstoudt
Posted On: 3 Hours Ago
Replies: 12
Views: 432
0 Lectron Carbs: anyone used them?
Last Post: rejeanprimeau
Posted On: 3 Hours Ago
Replies: 4
Views: 161
0 Had to wait for the snow to fall to pick up my 73
Last Post: Kingrabbit
Posted On: 5 Hours Ago
Replies: 9
Views: 322
0 Exhaust compatability?
Last Post: Racepres
Posted On: 6 Hours Ago
Replies: 1
Views: 71
0 Grenade plate fix with XR1200 parts...
Last Post: wrkdWS6
Posted On: 7 Hours Ago
Replies: 71
Views: 14,259
0 KT - 2021 - You're In It Now
Last Post: sportsterpaul
Posted On: 7 Hours Ago
Replies: 77
Views: 14,377
0 2021 Iron Butt Rally
Last Post: ParrotHead
Posted On: 7 Hours Ago
Replies: 155
Views: 17,158
0 90" of Street-based FUN coming downunder
Last Post: ParrotHead
Posted On: 7 Hours Ago
Replies: 351
Views: 70,551
0 Food porn
Last Post: Stairman
Posted On: 8 Hours Ago
Replies: 2,560
Views: 609,520
0 Hottie of the day, no nudity.
Last Post: Stairman
Posted On: 8 Hours Ago
Replies: 33,071
Views: 3,898,803
0 video & pics
Last Post: cal43
Posted On: 14 Hours Ago
Replies: 579
Views: 61,337
0 Hot Chicks on Hot Bikes
Last Post: cal43
Posted On: 14 Hours Ago
Replies: 12,616
Views: 2,987,745
0 Hot Rods, Rat Rods, and Customs.
Last Post: cal43
Posted On: 14 Hours Ago
Replies: 4,816
Views: 960,626
0 This is gonna hurt.
Last Post: cal43
Posted On: 14 Hours Ago
Replies: 9,088
Views: 2,127,634
0 Sportster Builds
Last Post: shanneba
Posted On: 15 Hours Ago
Replies: 9
Views: 349
0 What song do you have stuck in your head?
Last Post: Fivecats
Posted On: 21 Hours Ago
Replies: 2,456
Views: 265,298
0 Deer hunting at stairman's.
Last Post: Ireeman
Posted On: 1 Day Ago
Replies: 54
Views: 4,455
10 1983 XR 1000 Starting Issues.
Last Post: ChinCactus
Posted On: 1 Day Ago
Replies: 10
Views: 532
More...
Members Birthdays
Greg81XLH (56), saylor01 (55), Alicia (53), latnyte (52), antonini (44)
Tags
install front end, install show fork

Reply
 
Share Thread Tools Display Modes
  #1  
Old 1 Week Ago
XLXLXL XLXLXL is offline
Biker
 
Join Date: Jan 2019
Posts: 28
Sportster/Buell Model: XLCH 1000
Sportster/Buell Year: 1973
Reputation: 74542
XLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud of
Question 35mm Showa Installation Procedure? Tighten Sequence?

Amateur here, so I have showa 35mm fork front end setup with dual disc narrow glide for my ironhead, the top inner tube has a tapered style with top stanchion cap bolt. I think I run a small curiousity in installing the front end. sometimes the steering is just to tight, preload is too tight. the question, what is the sequential bolt/nut tightening for this setup?

My sequence was started with all installed in loose
1. Tighten the stanchion top for the bolt to the upper triple three.
2. Once the inner tube snugged in, then I tightened the pinch bolt in lower triple three
3. Tighten the top stem cap nut on the stem until it close to the steering still loose enough to move, but no slack in lateral movement, or longitudinal
4. finally tighten the pinch bolt for the stem cap nut.

Did I do it right? or there is some other combination for these sets? My friend suggested different method, here:
1. tightened the pinch bolt in lower triple three
2. Tighten the top stem cap nut and its pinch bolt
3. Tighten the stanchion top bolt.

thx folks
Reply With Quote
  #2  
Old 1 Week Ago
BigMek's Avatar
BigMek BigMek is offline
XL FORUM TEAM MEMBER
 
Join Date: Jul 2015
Posts: 326
Sportster/Buell Model: XLH
Sportster/Buell Year: 1982
Reputation: 362264
BigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond repute
Default

Your order looks fine. You want to tighten the fork cap nut first to fully seat the tapers.

If the steering is too tight, you need to set the fall-away by adjusting the stem cap nut torque. In my experience small adjustments make a big difference on the fall-away. You want the front end to be stable when pointed straight ahead, but "fall away" from center with a light nudge.
Reply With Quote
  #3  
Old 1 Week Ago
XLXLXL XLXLXL is offline
Biker
 
Join Date: Jan 2019
Posts: 28
Sportster/Buell Model: XLCH 1000
Sportster/Buell Year: 1973
Reputation: 74542
XLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud ofXLXLXL has much to be proud of
Default

Quote:
Originally Posted by BigMek View Post
Your order looks fine. You want to tighten the fork cap nut first to fully seat the tapers.

If the steering is too tight, you need to set the fall-away by adjusting the stem cap nut torque. In my experience small adjustments make a big difference on the fall-away. You want the front end to be stable when pointed straight ahead, but "fall away" from center with a light nudge.
thx for the respond. sorry just to clarify about the "fall-away", it means the play of the front end going up and down? if it is too loose, surely we can feel the front end have play up and down. Sorry, I come from a country where English is not my major language.

But I think I understand the nudge, you just need to torque the stem cap nut to the point where the we can nudge the steering easily from center. is that so?

thx again
Reply With Quote
  #4  
Old 1 Week Ago
BigMek's Avatar
BigMek BigMek is offline
XL FORUM TEAM MEMBER
 
Join Date: Jul 2015
Posts: 326
Sportster/Buell Model: XLH
Sportster/Buell Year: 1982
Reputation: 362264
BigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond reputeBigMek has a reputation beyond repute
Default

The stem cap nut should be torqued so, with the bike on a lift, the front end will stay put when pointed straight ahead but will "fall" to either side when nudged gently. By "fall" I mean it will go all the way to either side without you having to keep pushing it.

There should be no noticeable up-and-down movement at all. My method is to tighten the stem nut until the front end won't fall away at all, then loosen it until it does. Go slowly, a small change can make a big difference.
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT +1. The time now is 03:16.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
XL Forum® - Linson Media LLC