The Sportster and Buell Motorcycle Forum - The XLFORUM®
 

Go Back   The Sportster and Buell Motorcycle Forum - The XLFORUM® > SPORTSTER MOTORCYCLE FORUM > Sportster Motorcycle Motor / Engine > Sportster Motorcycle Motor - Top End
XLF Blogs XLF Arcade XLF Disclaimer/Privacy Statement/Terms Of Use

Sportster Motorcycle Motor - Top End Discuss Sportster Motorcycle Top End issues. Rockerboxes, Valves, Cylinders, Pistons, Rings, Lift Rods, etc...

Active Threads
0 I'm gunna need more Bourbon (pics)
Last Post: iNSaNeSHaNe
Posted On: 12 Minutes Ago
Replies: 5
Views: 69
0 Sportster leaking fuel from small tube underneath bike.
Last Post: iNSaNeSHaNe
Posted On: 28 Minutes Ago
Replies: 4
Views: 37
0 1968 xlch
Last Post: Moon Wolf
Posted On: 38 Minutes Ago
Replies: 5
Views: 88
0 Excited to join the sportster family!
Last Post: jharback
Posted On: 40 Minutes Ago
Replies: 4
Views: 41
0 2-1 Header Pipes
Last Post: iNSaNeSHaNe
Posted On: 44 Minutes Ago
Replies: 8
Views: 201
0 A thank you
Last Post: Hippysmack
Posted On: 1 Hour Ago
Replies: 3
Views: 39
0 Do you have the service manual?
Last Post: Crusty
Posted On: 1 Hour Ago
Replies: 726
Views: 183,310
0 Seized Oil Pump
Last Post: Hippysmack
Posted On: 2 Hours Ago
Replies: 21
Views: 483
0 Flat Tire
Last Post: Toejam503
Posted On: 3 Hours Ago
Replies: 31
Views: 1,730
0 forward controls vs. "normal" / trades?
Last Post: oupa
Posted On: 3 Hours Ago
Replies: 9
Views: 112
0 Motorcycle cafe suggestions
Last Post: oupa
Posted On: 3 Hours Ago
Replies: 17
Views: 1,146
0 compression problems
Last Post: Toejam503
Posted On: 3 Hours Ago
Replies: 34
Views: 682
0 Rubbermount shocks on a rigid mount?
Last Post: Toejam503
Posted On: 3 Hours Ago
Replies: 8
Views: 107
0 Cafe or sport faing on xl1200cx?
Last Post: noxlyet
Posted On: 3 Hours Ago
Replies: 21
Views: 3,322
0 Mainshaft- What happened here
Last Post: Bwf347
Posted On: 4 Hours Ago
Replies: 48
Views: 3,641
9 Been a long time! !
Last Post: Texassporty06
Posted On: 4 Hours Ago
Replies: 17
Views: 1,237
0 Wanted: Sportster mid controls
Last Post: racemoto
Posted On: 4 Hours Ago
Replies: 4
Views: 45
0 Are the 04s the red headed step child?
Last Post: wedge
Posted On: 4 Hours Ago
Replies: 46
Views: 1,851
0 Finding a new doctor...
Last Post: Hippysmack
Posted On: 4 Hours Ago
Replies: 17
Views: 255
0 This week on Craig's list
Last Post: Wilkinson949
Posted On: 4 Hours Ago
Replies: 3,751
Views: 415,213
0 What brand synthetic oil do you use
Last Post: Akdawg
Posted On: 4 Hours Ago
Replies: 382
Views: 97,360
4 The no-debate OIL POLL
Last Post: 60Gunner
Posted On: 4 Hours Ago
Replies: 216
Views: 58,841
0 one sporty and $5000... What would you do?
Last Post: Jarlaxle
Posted On: 4 Hours Ago
Replies: 288
Views: 135,122
0 Forum problems???
Last Post: oupa
Posted On: 4 Hours Ago
Replies: 34
Views: 972
0 Lets see your off season builds
Last Post: cycowrencher
Posted On: 5 Hours Ago
Replies: 1,233
Views: 151,409
0 Food porn
Last Post: Ireeman
Posted On: 5 Hours Ago
Replies: 1,158
Views: 188,281
3 Wtb, Wts, Wtt, Wtg (Ironhead)
Last Post: hawgford
Posted On: 6 Hours Ago
Replies: 77
Views: 217,886
0 Hottie of the day, no nudity.
Last Post: Stairman
Posted On: 6 Hours Ago
Replies: 9,909
Views: 866,089
0 Motorcycle Events
Last Post: rhartlin
Posted On: 6 Hours Ago
Replies: 8
Views: 2,434
0 Bendix / Zenith questions
Last Post: hawgford
Posted On: 6 Hours Ago
Replies: 41
Views: 19,584
More...
Members Birthdays
Sponsored Links
Reply
 
Share Thread Tools Display Modes
  #1  
Old 15th September 2018
t120r t120r is offline
XL FORUM TEAM MEMBER
 
Join Date: Jan 2009
Posts: 85
Sportster/Buell Model: xl883r
Sportster/Buell Year: 2003
Reputation: 3596
t120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rough
Default Machining for 30 degree chamber

Just postulating about how hard it would be to cut my own 30 degree chambers. I have a Bridgeport and a rotary table... Being in Canada means outrageous shipping costs and border fees. Hard to justify sending heads out for that. Especially when I have a mill.
Reply With Quote
  #2  
Old 21st September 2018
bustert's Avatar
bustert bustert is offline
XL FORUM TEAM MEMBER
 
Join Date: Jul 2008
Posts: 8,784
Sportster/Buell Model: 1200s
Sportster/Buell Year: 2001
Sportster/Buell Model #2: xlch
Sportster/Buell Year #2: 1974
Reputation: 1550747
bustert has a reputation beyond reputebustert has a reputation beyond reputebustert has a reputation beyond reputebustert has a reputation beyond reputebustert has a reputation beyond reputebustert has a reputation beyond reputebustert has a reputation beyond reputebustert has a reputation beyond reputebustert has a reputation beyond reputebustert has a reputation beyond reputebustert has a reputation beyond repute
Default

never know til you try
Reply With Quote
  #3  
Old 21st September 2018
t120r t120r is offline
XL FORUM TEAM MEMBER
 
Join Date: Jan 2009
Posts: 85
Sportster/Buell Model: xl883r
Sportster/Buell Year: 2003
Reputation: 3596
t120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rough
Default

That's what i figured. If i use a wide ball end bit on a 30 degree angle, i can get it pretty close to perfect. Hardest part will be measuring to match the piston.
Reply With Quote
  #4  
Old 21st September 2018
Turbo Sporty 48 Turbo Sporty 48 is offline
Master Custom Bike Builder
 
Join Date: Sep 2010
Posts: 3,344
Sportster/Buell Model: XL1200X Turbo 48
Sportster/Buell Year: 2011
Sportster/Buell Model #2: XL1200 Roadster
Sportster/Buell Year #2: 2008
Turbo Sporty 48 has disabled reputation
Default

How about claying the head to get your clearances?
There is probably something better than modeling clay but you get the idea.
Reply With Quote
  #5  
Old 21st September 2018
t120r t120r is offline
XL FORUM TEAM MEMBER
 
Join Date: Jan 2009
Posts: 85
Sportster/Buell Model: xl883r
Sportster/Buell Year: 2003
Reputation: 3596
t120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rough
Default

Sorry, i don't think i explained what i meant. With a 3.5" bore piston, for example, does the edge of the 30 degree quench pad end at 3.5"? Does it go a few thou wider or narrower due to the gap between piston and wall?
Reply With Quote
  #6  
Old 22nd September 2018
rocketmangb's Avatar
rocketmangb rocketmangb is offline
XL FORUM TEAM MEMBER
 
Join Date: Jan 2008
Location: So Cal
Posts: 20,724
Sportster/Buell Model: XL1200C
Sportster/Buell Year: 2006
Sportster/Buell Model #2: XL1200C
Sportster/Buell Year #2: 2006
Other Motorcycle Model: 48 "Totalled" By a Douche
Other Motorcycle Year: 2012
Reputation: 3376039
rocketmangb has a reputation beyond reputerocketmangb has a reputation beyond reputerocketmangb has a reputation beyond reputerocketmangb has a reputation beyond reputerocketmangb has a reputation beyond reputerocketmangb has a reputation beyond reputerocketmangb has a reputation beyond reputerocketmangb has a reputation beyond reputerocketmangb has a reputation beyond reputerocketmangb has a reputation beyond reputerocketmangb has a reputation beyond repute
Default

I could check my spare 1250 heads if you like ?
__________________
Thy Sportster Come
It Shall Be Done
On Earth as it is on Salt
2006 Sportster XL1250C
Hammer Sledge Heads 1.98X1.61 Valves
Hammer 600 Cams
Big Ass CP/Hammer Pistons
Mikuni HSR 45 /Hammer Billet Manifold (Now HSR 48)
Jetted 27.5 slow,182.5 Main
97 Needle,Clip posistion 3
Hurricane Flow 3" offset AC,Rocketman Mod
Daytona Twin Tec TC88A,Rico Scarecrow Map
Sumax Thundervolt plug wires,NGK DCPR8EIX spark plugs. Gapped .040 and Indexed
Cycle Electric Stator and Regulator
Alto Carbonite Clutch
Royal Purple 20W50 MC Primary oil
Patriot Defender Pipe
Royal Purple 20W50 MC Engine Oil
Napa 7148 oil filter
Max Power, 111.47
Max Torque, 84.39
Best 1/4 Mile ET to date 11.85
Best 1/4 Speed to date 115.14
Build by Jester Motorwerkz West
Reply With Quote
  #7  
Old 22nd September 2018
t120r t120r is offline
XL FORUM TEAM MEMBER
 
Join Date: Jan 2009
Posts: 85
Sportster/Buell Model: xl883r
Sportster/Buell Year: 2003
Reputation: 3596
t120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rough
Default

That would be great Thank you.
Reply With Quote
  #8  
Old 22nd September 2018
aswracing's Avatar
aswracing aswracing is offline
A Million Facts & Figures
 
Join Date: Jan 2005
Location: Famous Potatoes
Posts: 9,931
Sportster/Buell Model: XL883
Sportster/Buell Year: 2007
Sportster/Buell Model #2: Buell Cyclone
Sportster/Buell Year #2: 1999
Reputation: 2175181
aswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond reputeaswracing has a reputation beyond repute
Default

Quote:
Originally Posted by t120r View Post
Sorry, i don't think i explained what i meant. With a 3.5" bore piston, for example, does the edge of the 30 degree quench pad end at 3.5"? Does it go a few thou wider or narrower due to the gap between piston and wall?
We cut them .030" smaller than the bore size, because the crown of the piston is smaller than the bore. If you cut it at the bore size, you'll never get a tight squish clearance. Getting it centered over the bore is also important.
__________________
Click Here to Contact Me

Reply With Quote
  #9  
Old 22nd September 2018
sportysrock's Avatar
sportysrock sportysrock is offline
Senior Master Custom Bike Builder
 
Join Date: Jul 2005
Location: Disinformation Superhighway Exit 54
Posts: 4,377
Sportster/Buell Model: XL883H/1200H
Sportster/Buell Year: '96
Sportster/Buell Model #2: XLCH 1000 w/elec. leg too
Sportster/Buell Year #2: '72
Reputation: 437003
sportysrock has a reputation beyond reputesportysrock has a reputation beyond reputesportysrock has a reputation beyond reputesportysrock has a reputation beyond reputesportysrock has a reputation beyond reputesportysrock has a reputation beyond reputesportysrock has a reputation beyond reputesportysrock has a reputation beyond reputesportysrock has a reputation beyond reputesportysrock has a reputation beyond reputesportysrock has a reputation beyond repute
Thumbs up

Quote:
Originally Posted by aswracing View Post
We cut them .030" smaller than the bore size, because the crown of the piston is smaller than the bore. If you cut it at the bore size, you'll never get a tight squish clearance. Getting it centered over the bore is also important.

You are awesome for sharing tech info - as always, and really make the forum great! Rep to you guys.
__________________
Ol' Big Daddy of the Dirty Ducks MC
I'll see your Twin Cams and raise you 2 more
Unlike the Internet, Al Gore DID INVENT Global Warming
Political Correctness never killed any terrorists.
Reply With Quote
Sponsored Links
  #10  
Old 22nd September 2018
t120r t120r is offline
XL FORUM TEAM MEMBER
 
Join Date: Jan 2009
Posts: 85
Sportster/Buell Model: xl883r
Sportster/Buell Year: 2003
Reputation: 3596
t120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rought120r is a jewel in the rough
Default

Thank you for the info. Once the weather ends the bike season here, I'll be ripping my heads off. I'll decide if I want to keep these Edelbrock heads or not (Love the look) and if so, I'll order up a 1275 kit. Unless I screw up my chamber... Then I'll go to 88 or 90cid and retry the chamber again.
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Sponsored Links
All times are GMT +1. The time now is 07:37.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
XL Forum® - Linson Media LLC